Posts

Chosen Solution My radio receives a signal, or it may be on CD. Unpredictably, the sound cuts off, then comes back, over and over. May be OK for hours, or misbehave every few minutes. Hi @bobrich18 Looking at the service manual the Volume Control is designated as component #VR701 which has a Sharp component part #QSW-ZA002AWZZ. This is a rotary encoder type control switch and not a resistive potentiometer type control switch....

Chosen Solution Is it possible to take out the MLC NAND flash and convert into some sort of external hard drive to extract the data from my iPod Touch that cannot be brought back to life? If the answer from Majesty should not work for you, there is still another way. But you better know what you are doing and have some really good skills. The problem that you might be run into is that your logic board, or at least one of its circuits, is non-functioning....

Chosen Solution What to do: Utilize diagnostic portFind documentationGet any shematicsPatent/legal documents describing functions @oldturkey03 @mayer @theimedic @refectio @jayeff @danj @jimfixer If I missed anyone else say so. What’s everyone got? @pccheese - Sorry George Apple has held its cards real tight here on any documentation in repairing them. Even authorized service centers don’t fix them, only ship them out to Apple.

Chosen Solution Got a broken iphone 5 from my friend a while back, it’s pretty horribly cracked. Still 100% functional, i can touch it all and it works, but lately pieces have been falling off of it and I’d really rather that stop. I fix computers, but not really touch screens, let alone phones. So my question is, since the touch screen part still works, do I need to replace the whole digitizer for 200 bucks or can I just replace the LED screen for 20?...

Chosen Solution When you turn the dial at the front the mechanism drops stopping the mixer low speeds but works at high speed. Is this something I can fix and if so how? Try this guide for the a low speed fix: How to adjust Kenwood Chef A701A minimum speed

Chosen Solution I have HCL 15.6" TFT LCD wide color monitor model-Y156W There is thin vertical red line appearing in monitor screen PLZ solve my prob @sumangal those lines are usually caused by a TAB error. The bonding of the very thin ribbon cable entering the LCD may have come off or broke. Apply some pressure to the cable at exactly the point where the lines appears. If that changes the line, than it is a TAB error....

Chosen Solution PS4 stuck in safe mode Everytime i turn ps4 on it checks system storage status then goes to menu tells me cannot start ps4 connect controller and press ps button then it tells me i need update file version 5 and i put i USB with update file it tells me update file cannot be used error code CE-34788-0 but when i start PS4 in safe mode (7 seconds on power button) it installs the update but after restart safe mode again please help...

Chosen Solution Golf cart ran completely out of gas, now fuel not getting to fuel filter. Ran perfectly till ran out of gas. You need to look into what type of fuel transport you have: a) gravity b) electric pump of c) mechanically driven from engine camshaft etc. Also sometimes vehicles that only get sporadic use can get clogged up with crud in the fuel tank and running it fully out can lead to coating any mesh sock type filter at the intake point inside the tank with particles that could lead to problems getting the pumping of fuel going again....

Chosen Solution Does anyone know why its becoming nearly impossible to do fresh installs of OS-X on older Mac Systems. I have had a collection of various versions of OS-X installs set up on USB sticks. Have been using them with no bother for the past 5 + years. In the last 6-12 months they have all stopped working. When I try to re-burn them and use them the Mac system is saying the install has become corrupt....

Chosen Solution Do you sell the rear microphone of the iPhone 6S Plus? If so, do you have the video of how to replace it? What tool kit do I need to do it? iPhone 6s Plus Power Button Cable Assembly Replacement This is the rear mic, make sure you get one with the long metal bracket already attached. I believe that the rear microphone is soldered onto the the charging port flex cable....

Chosen Solution how do i remove lower intake manifold First remove the upper air chamber then remove the fuel rails and injectors make sure you have drained the engine coolant completely before unbolting the intake then once the coolant is out remove the bolts that secure the intake and pry from a corner to break the seal of the old gasket. If you go to youtube you can usually find all sorts of videos on this....

Chosen Solution I wanted to replace MinoHD battery. Can I do this? You can definitely change out the battery although its clear the mfg would rather you buy a new flip for $165.00. Remove the cover very slowly and carefully so you don’t break the ribbon cable. You can then unplug one end of the cable and leave it in the socket on the other end. Carefully fold over the display and be careful because the mylar backing is glued down....

Chosen Solution Apple wired keyboard Is it possible to re-attach the F18 function key back onto the Apple extended aluminum wired keyboard? It is possible to replace the key as long as the tabs on the back of the keycap are not broken, the scissor assembly is intact and unbroken and the rubber bumper is still attached. If the scissor came off with the keycap you will need to disconnect it from the back and attach it to the keyboard first....

Chosen Solution Just replaced my iPhone 6 LCD screen, the repair went flawlessly aside from now about a quarter of ,y screen is black with a few rainbow wiggle lines. I can still type and use the areas that are covered by the black out…so I’m just wondering where I could have gone wrong. Sounds like a LCD connection issue. First try reseating the LCD connector for the screen. Does the old screen still showed display before?...

Chosen Solution Dear All I have Galaxy S5 SM-G901F. My device have problem of self restarting. Due to this issue battery discharge very quickly. Please anyone if you know the solution please guide tabassum.shehzad1@gmail.com most likely you need a new battery. try a new one like richard said did it get wet? if not have you tried a new battery? Update (01/31/2017) might be got wet or damaged power ic

Chosen Solution Repair was completed by a third party - initial problem was a non-working LCD from a drop; everything else works fine (tested in diagnostics) Tried every software based solution (e.g. settings reset, reboot, cache deletion). As tested in diagnostics, front camera works but rear camera says “camera failure”. No physical damage on the camera at all. Would this just be a disconnected cable? Yes, a loose or partly connected flex could be an issue....

Chosen Solution printer is fairly new… all of a sudden while copying and scanning..it prints and scans what t looks like a lot of thin lines that makes this half inch line all the way down the paper. Clean all scanner glass with windex or rubbing alchohol. Look for any marks or smudges on the glass. I have seen white out cause all kinds of problems on scanner glass, but it should be easily repairable....

Chosen Solution It happens especially when using graphics or video programs. I tried everything. Would you please give me some advice? reset NVRAM - donereset SMC - donenew fresh installation - doneI connected the second monitor, and the flickering continues on the second screen at the same time.I used the screen recording, and everything seems fine in the record; there is no flickering in the screen record, but there was a lot of flickering in real-time....

Chosen Solution I have put a new screen on my iPhone 4s as my old one was smashed. At first it was fine for about 24hrs then suddenly my phone went a bit mad with a striped screen and then it went black. I plugged it in to my charger however it beeps constantly and didn’t come on. After trying a couple times and plugging it into my laptop it eventually came on....

Chosen Solution When I switch on the screen is bright but after twenty seconds or so the screen goes dim. Hi, You don’t state the model number of the tablet so hopefully the follow settings are also available in your particular Samsung tablet. Go to Settings > Display and Wallpaper and adjust the following settings to suit: Smart stay: Set the device to prevent the display backlight from turning off while you are looking at the display....