Chosen Solution TV comes on but says select the source button when I press enter nothing happens. Unable to select anything @choui could be an issue with the button bar or with the main board. You do want to give us the complete model number for your TV. Also, start of by unplugging the set and every component you may have plugged in to it. Let it sit for 15-20 min....
Chosen Solution I have replaced my screen and digitiser. When refitting the logic board I was having trouble putting in the top centre screw. When removing the logic board to see what the problem was, I found a loose grounding clip underneath it. It has provision for a screw to pass through it with a grounding dimple to the side. I would attach a picture but not sure how to through a URL link....
Chosen Solution Hey Everyone, I changed the Digitilizer and the LCD on an Ipad Air as it was broken and showed nothing on the screen. After the repair it shows an uneven lightning on the left side of the screen. Attached are some pictures of the screen. What is strange to me is that there sometimes is an even unevener lightning with only 3 spots on the left side Some times the screen wont turn on at all and you just can restart the ipad to get it to show something again....
Chosen Solution I need to replace the fan in my Macbookpro. The problem is that there is a stripped screw on the back of the Macbook. How do I remedy the problem without taking it to the genius bar? You need a jeweller’s screw extractor. Look for for a jeweller’s tool supply firm. You will need to look around a bit for it as they are much smaller than the ones you normally find at machine shops....
Chosen Solution my tablet has a yellow robot picture with the words KERNEL PANIC UPLOAD MODE to reset the tablet you’ll need to disconnect the battery and reboot the tablet . this shows how to pull the battery. you dont have to remove the battery just disconnect for a minute then reconnect and boot this should fix you right up https://www.youtube.com/watch?v=m3lyA5p-… Hope this helps
Chosen Solution Entire tail broke off and strings are just hanging and tail in many pieces. How to fix this? Looks like it’s a bunch of clips, that the tail pieces just get pressed together. Heres a guide that gives a little insight to the situation Zoomer Dino Boomer Tail Tip Replacement Same problem: the whole tail fell appart. There are four strings and I don’t know how to put them back in place....
Chosen Solution Hello! My name is Leopold. I have an Macbook Pro Early 2011 that is a bit ill. The symptoms is it is running hot the fan sounds weird as an result of that, the battery time is affected. I have tried making an recording of it with my iPhone 5 and put it on SoundCloud. Here is the link, it is a 10-seconds recording: SoundCloud. I have also tried using air to blow the fan clean....
Chosen Solution It started out booting up with yellow vertical lines and grey dots in the background and that was all you could see. When I boot into safe mode the lines are still there (sometimes) but at least I can see everything and get into what I want such as system preference in order to change the display settings. The first five times I fixed this by booting into safe mode and changing the display resolution from the default to something else....
Chosen Solution The headset symbol is not disappearing from the upper task bar. What could be the problem. 2. My MI4 is not working with some 4glite network sim. I will be very grateful if you could give me useful answers to my questions. Try updating the software on your phone to the latest version. Annoying “glitches” like a tenacious headphone icon are sometimes caused by an outdated software version. Also, see if doing a full factory reset of the phone’s operating system doesn’t help....
Chosen Solution I’m trying to replace dead led’s from my expensive aquarium lights but I am having a hard time removing the led diodes. I’ve tried using a hot air station at 500 celcius (932 Fahrenheit) but the led won’t budge. I tried blasting hot air from both the bottom and top but it won’t budge. I don’t have a heating plate so is there a better way? As you can see the bottom of the board is all metal....
Chosen Solution The ipad screen literally cracked at the top left and top right corners. I got the rest of the panel off, but can’t seem to get these two corners off as it is cracked into small pieces, heavily glued to the corner. Any tips on removing these micro shards in one piece or as easily as possible? A heat gun on low in 4-5 second increments and an iSeasmo....
Chosen Solution Just replaced my battery with a battery purchased from ifixit. However, my computer doesn’t seem to be recognizing the battery. From system report and coconut battery it shows that no battery are installed. I’ve tried all the troubleshooting methods like NVRAM /PRAM reset, SMC reset, repair disk permission but nothing has worked so far. It’s not the charger’s issue since a green light appears when plugged in. As well switching back to the old original battery, my computer recognizes it and shows that a battery is installed....
Chosen Solution Hello, I recently replaced the glass on my 13" 2012 MacBook Pro, however, I notice that the replacement glass is lifting off of the display assembly. I do wish to resolve this issue, however, am reluctant to turn to solutions such as superglue or cheap two-sided tape, unless it is a tried and true method. Is there a universally accepted method to making the glass stick to the assembly?...
Chosen Solution Hi there, I’m looking to replace the screen on my HTC One (M7 version). I have read a couple of your guides, and I just want to confirm that I need something like this rather than something like this. Obviously, if I could do just fine with the cheaper product, I’ll take that, but that’s what I’m a bit uncertain of. Thanks for your help! Martin It depends on the problem you’re display is experiencing....
Chosen Solution My coworker accidentally spilled about a bottle capful of water on to my MacBook 13" Aluminum Unibody Late 2008 (A1278) keyboard. He immediately wiped it up and told me about it. About 5 minutes later, I realized my keys “A” through “L” and keys “Z” through ,“M” weren’t working. I shut down my computer, took out the battery, and let it sit open and upside down (like a tent) for the remainder of the day....
Chosen Solution Hello, My Galaxy S4 phone tends for freeze up/lag a lot in the last month. It lags when: -My phone is locked and I hit the power or home button. The screen quickly flashes on and off, and will stay dark until a minute or two later when it finally releases itself and then I can use the phone again. -When I’m texting. The screen freezes and can’t type anything....
Chosen Solution This is a roughly new phone and shouldn’t be having problems. I got it a few months ago and it just started doing this about 2 hours ago. I had been walking and had my phone in my pants. It was not in a pocket but the screen was against my stomach. I have been listening to music and it suddenly shut off I take out my phone to see what had caused the music to stop....
Chosen Solution Hello, As I already wrote in the headline, The display is no longer working. I didnt replace The Display it was in an mobile Shop, but The Shop didnt exist anymore. The iPhone makes some noise if i Connect it with an Charger. Is the Backlight circuit damaged or is the Screen faulty and cheap? (the Backlight is completly DARK!) If you can’t make out an image at all on the display with a flashlight chances are it’s a bad screen....
Chosen Solution I followed the instructions to fix wobbly screen. Everything worked well. But when I switched the macbook on, i hear it startup but the screen stays blank. Could I have knocked something? Anyone have any ideas of what I should check? Thanks Go back to step #8 and reseat the display data cable, examine the connector and the slot. Make sure the little lock tab that hold it in place will throw down....
Chosen Solution Printer companies really are not in the business of making money selling printers. They are in the business of selling ink. They go to all kinds of effort to make sure that only their products will work in their machines. Laser printers such as HP even put chips in their cartridges to prevent you from filling them. They have expiration dates so that sometimes a brand new toner won’t work because it is to old....
