Chosen Solution After i replaced my digitizer and lcd, i encountered ghost touches and unresponsiveness in the first row from the top of my iPhone. Later on, when I was trying to figure out what the problem was, the the 2nd row from the top also became unresponsive. Now I am stuck in the setup stages after restoring my iPhone and cant get past it because i cant use the top of my iPhone....
Chosen Solution PS5 came into my shop for a broken HDMI port. The HDMI port was replaced successfully, ps5 was reassembled, tested, and returned to the customer. The customer then called back reporting that it was shutting off on them. I directed him to bring it back in, we tested it, and it didn’t shut off for us while he was standing there. We waited for about 5 minutes for it to shut off and I asked him how long it normally takes....
Chosen Solution So, I have this iPad mini 4 which the Touch ID works, but the home button doesn’t. Is there a way to just replace the home button clicking part? Have you recently replaced the screen or have had it opened before the problem? Yes, you can replace the home button to get it working again or you can open it to make sure it is making proper contact with the pads that make the physical connection....
Chosen Solution How to replace ram with larger ram? Sorry, you can’t replace the RAM in this phone. It comes with 2 GB of RAM on the SoC module. The phone came with two flash storage versions 16 or 32GB which is soldered to the logic board. Sadly, this model does not come with a SD slot so you can’t add flash storage that way either.
Chosen Solution I am tearing down my jeep and building it into a rick crawler well i want to. But im not sure how to go about it and what should be done first. @amg925, Aleese , You will have to decide on a budget firstly, as this could be an expensive venture. I think you are probably best to check out Jeep/rock crawler forum’s,etc. to see what it really takes to build/convert to achieve a successful rock crawler....
Chosen Solution Well…I’m the idiot. When swapping out my ram, I broke the tabs that keep the ram boards in place. (See step 4 - RAM in the topic called “Installing MacBook Pro 15” Core 2 Duo Model A1211 RAM"). What part(s) do I need to replace? Apple says I need to replace the mother board. But when I look at the mother board, it doesn’t show the ram assemble/tabs. Any ideas?...
Chosen Solution The touch functionality has gone a bit wonky on my Surface Pro 2 (I get occasional “phantom touches” down the left side of the screen), so I’ve decided to roll the dice on opening it back up and replacing the LCD assembly. Looking at the replacement LCDs available (including the ones that iFixit used to sell), they all appear to be missing a plastic bracket that surrounds the space where the the front facing camera peers out of....
Chosen Solution Hi, I have a Macbook Pro A1211 2.16Ghz system that I recently upgraded to Yosemite. I was very happy again that my laptop had a new life. About two weeks after the graphics card died. Black screen and no DVI output either but got the bootup chime. Tried everything it fix it. Google made it sound like the GPU fried. I rather not replace this logic board with the same one....
Chosen Solution Of the two attached pictures, one shows the sliding switch in the “in” position, the other shows it in the “out” position. The only reference in the owner’s manual I can find is that this is where the “cable CARD” slides in: https://www.manualslib.com/manual/361664… Does anyone have any ideas as to what this switch is for? It sits next to the fan. The TV is currently not working, probably needs a new power supply board....
Chosen Solution Model Code: PN42C430A1DXZC TV will not power on. There is no backlight or picture on the screen. There is a standby light on. When I attempt to power on the TV, there are clicks coming from what I think is a relay, the light goes off for about a second, then it is back on solid. No visibly blown capacitors or burnt components on the power supply board. The following are the voltages taken from CN801:...
Chosen Solution Samsung Top Load Washer AW40J3000… Washer Fills but then it just has a humming sound it will not agitate, spin or drain. @mamkugs I’d start by checking the lid switch (unlikely) and the belt (Number 1 suspect)that connects the motor to the transmission. A broken belt would cause you to hear the humming from the motor without any movement of the tub.
Chosen Solution Says repairing disk errors this may take over an hour but never completes Update (02/26/2017) Says repairing this peers this might take over an hour to complete but it never does complete I would cancel the repair attempt. Back up all your data on another hard drive. If the computer is under warranty, have the hard drive checked by the manufacturer. If not under warranty, change the hard drive out....
Chosen Solution Over time my MacBook has been developing an issue, at first when I pressed the bottom area of the screen bezel it starts doing something I don’t really know how to describe, so I attached a photo, and the screen is noticeably dimmer. Currently I don’t have to do anything for it to happen, and even worse, sometimes it flickers, however the backlight never fully turns off. I tried running the laptop with the bottom off and pushing the display cable, but it didn’t do anything, so I’m assuming it’s something inside the display....
Chosen Solution I have an Htc desire hd phone and my half screen is cracked but the phone still work smoothly..I want to know that whether i have to replce my whole LCD screen or i have to replace my Screen digitizer glass lens only??? Pls help Me« Hi Amit, If there is no defect in your LCD and your phone still works smoothly (as you mentioned), then only the digitizer glass is broken (although it still works)....
Chosen Solution when i started my phone it was a iTunes icon and a iPhone charger and later it was only black and when i started the phone again it was same Plug into iTunes and restore
Chosen Solution Recently my tablet’s display has gone blank; I can turn on the power and hear the tablet turn on, but the display stays blank. I’ve tried cleaning the display and then tapping it to ensure it just isn’t in sleep mode, but it didn’t appear to help; still no response from the tablet Follow these steps and you will manually boot your device: Press and hold the VOLUME DOWN button, and then briefly press the POWER button....
Chosen Solution I just installed a new Crucial M500 drive into my 2009 2.0 GHz Mac Mini. I created a bootable USB using Disk Creator and attempted to boot from it so I can load the OS onto the new drive… but I keep seeing the No Entry icon. Did I need to format the SSD first? I have no idea how to load a fresh OS onto the new drive and could use a pointer in the right direction....
Chosen Solution Both of my Blu phones, the Vivo Air ,are not reading the sim cards, any idea as to why. ?? They worked fine for 12 months, I used Tesco in England, then changed back to T Mobile here, that’s when neither went back to working. there are two types of networks, CDMA and GSM. CDMA SIM cards are not compatible with GSM phones, and vice-versa. Also, if you have not unlocked your phone from it’s carrier and are trying to use a SIM card from another carrier, it will not work....
Chosen Solution The mousepad has some peeling to it and sometimes freezes in the middle of the screen for a small amount of time. Also left click mouse button is no longer responsive although right click is how can I fix this? Hi @alliet , It seems as though the best option is to replace the touchpad and the mouse buttons. They are an integral part of the laptop’s palm rest assembly, so to replace them you will have to replace the entire assembly....
Chosen Solution I have taken apart Iphone 5SE to replace a crack screen. In the progress i have lost the spring contact that goes underneath the screw that connects heatsheild to the screen, through home button ribbon Is it important or can i get away with the phone working without ordering a new one ? I couldn’t tell the difference or without it installed for the home button flex it’ll work fine without it....
