Chosen Solution So here’s my dilemma: I was trying to get my text messages from my iPhone 4S transferred to my PC. One of the things I attempted to do was use iTunes on my PC to create a backup by choosing “Restore from Backup”. So I connected my phone to the PC using a USB cable. When I ran the process, though, it ended up upgrading my iPhone to iOS 9....
Chosen Solution Hi My iPhone’s back camera is quite temperamental and sometimes if dropped disconnects and doesn’t work - I know the problem is not that the camera is broken only that it is a connection problem because I have fixed the issue before. This time, after putting my phone back together the phone will not turn back on at all. Itunes recognises the device (however I can’t restore it because I can’t respond on my iPhone when prompted to allow the computer access)....
Chosen Solution how to replace blower motor resistor in 1999 dodge dakota wayne rients here is the way the manual describes it: REMOVAL - BLOWER MOTOR RESISTOR BLOWER MOTOR RESISTOR (1) Disconnect and isolate the battery negative cable. (2) From the passenger foot well area, remove the two hex screws used to secure the blower motor resistor. (3) Unplug the front blower motor resistor from the wire harness connector. (4) Pull the front blower motor resistor and its wire harness out of the plenum panel and through the cowl plenum access hole far enough to access the wire harness connector....
Chosen Solution I recently replaced my Macbook Pro’s battery. When I completed the last step, I rebooted my Macbook and everything was perfect except for the keyboard. Not one key worked - not even the power button. The only way to get it to boot has been to disconnect the battery cable and plug in the MagSafe power cord. After about 10 seconds, the laptop boots, just be virtue of the fact I’ve connected it tp AC power....
Chosen Solution After I put the new HD in and partitioned the drive, the install took forever, multiple hours. Once it finally finished the computer was crawling. I mean slow… every click the wheel would come up and spin. It’s a brand new HD. My previous HD failed… hardware test came back with 4HDD/11/40000004:SATA(0,0) So I am starting from scratch with no back up You’re hitting a known issue here! You’ll need to replace the SATA cable....
Chosen Solution So i think my 2ds sleep slider is broken (it randomly goes into sleep mode).I have another 2ds with a broken card reader, can i change the sliders between them? Yes, you can change parts between the two items. I would recommend disconnecting the battery on both units before performing this procedure(you can put them back in once the procedure is done).
Chosen Solution Hello guys, my curved LCD Smart TV (UE55KU6652U Series 6) started to have one thick black line over a half of the screen. This line is also visible when the TV is switched off. Do you think TV screen is cracked or is it any component that can be repaired? Thank you, L.P. Lada Pazderka that is a damaged LCD. Not much you can do about it. Replacement panels are pretty much non existing and if you should find one it will most likely cost more that a new TV....
Chosen Solution The washer will not power on when the power button is pushed. It did turn on intermittently (once every 5-10 times) for a few days, but not at all now. The main control board (right side) is flashing green every 5 seconds which I believe means it is functioning, or at least getting power. See photo: When I push the power button, I hear a clicking sound and a green light on the smaller control board (left of photo) flashes 7 times, then goes off....
Chosen Solution Does anybody have the schematics of Samsung Monitor S24E650PL Model code: LS24E65UPL/EN PCB: SE650PCB Grateful for any help, Edsel I don’t have that exact model, but I do have the Service Manual for the S24A350H. It may be of use to you. Samsung_s22a350h_s23a350h_s24a.pdf (For future searchers: Samsung Monitor Service Manual S22A350H, S23A350H, S24A350H, & S27A350H, Chassis: L3S22HS, L3S23HS, L3S24HS, & L3S27HS)
Chosen Solution screen frozen, but phone rings when called, unable to answer,phone fully charged sally booth your question is not very descriptive. If your display is frozen, try a reset. If your display is okay but your touchscreen does not work, replace that. Use these guides to work on your phone.
Chosen Solution Hi, I just installed new screen on my Iphone 6s. Screen works good, but after turning on mobile data or calling, screen started to generate random touches. When I turn data off again screen works perfectly. Do you know where the problem can be? Bad aftermarket screen. It’s a static discharge issue caused by screen. I’m really surprised it happens on iPhone 6 series as usually it only happens on 5 series....
Chosen Solution Hi, so I made a scrrenreplacent and in the beginning the backlight wouldn’t work at all so I reinstalled the older one and it barely lights up, I looked through everything and this part right here could be the issue. (On the left) This Happened at the beginning probably while I was removing the ribon cables and I let my buddy try it but either he put too much force or the tool slipped while he was pulling it off....
Chosen Solution if my phone has a warranty it came with is replacement or repair under warranty That really depends on the sale of the phone. You need to contact or visit where you got the phone from. It’s possible it’s still under warranty. But I can’t say if it is or not
Chosen Solution I need to replace the screen on my Galaxy S5 Sport from Sprint. Do you have any special tear down instruction for this phone? I ask because the display cable is not found in the back of the phone. Hi the s5 sport is build very similar to the standard s5 and you can follow the screen replacement guide for the standard s5 to remove and replace the screen on your s5 sport....
Chosen Solution So I was wearing my boardshorts all day with my phone in my pocket and had gotten used to it. I totally forgot my phone in my pocket and jumped into my pool without noticing the phone. After 30 minutes of me and and my phone sitting in the pool I got out and felt the phone in my pocket and freaked out. So right away I went home and put the phone in rice....
Chosen Solution So for the past year my laptop has been having issues turning back on if it gets shut down completely (restarts are fine). After an event of it shutting down while I was on vacation and then not being able to turn back on, I took it to a repair shop just to see if they could diagnose the problem. I had some hunch it was the logic board as I just replaced the battery a few months ago since the original one was at the end of its life, and the guy confirmed that my SMC on the logic board is no longer working and that is also why no amount of SMC resets seemed to solve my issue (even though that is googles common answer for my laptop problems)....
Chosen Solution At the top of the page it says: iMac Intel 24" EMC 2134 and 2211 Repair Manual I have looked over the entire page, clicked on every link but I can’t actually find the manual? Am I blind or just thick? You’re not thick. The plan is to have a wiki repair manual for every device that gets better over time. For this iMac, we have parts, questions / answers, a description page about the device, but no step-by-step guides yet....
Chosen Solution During screen replacement the digitizer connection appears to have been pinched I cleaned with a toothbrush I used for cleaning.the plastic between contact appears to have moved or got pinched is there any repair or replacement for this connection No, screen needs to be replaced again. Once the ribbon cable gets physically damaged, the screen is no go.
Chosen Solution I tried to remove it but the screw is so tight that it started to get ruined and now i cant move it at all Try these Good Luck, N. You could try different screwdrivers. Generally only the center of the screw strips. Using a screw driver with a larger tip may work. If you have already removed one if the screws, wrap some tape around the threads (so it is harder to lose if you drop it) and take it to the hardware store or a good Electronics store (one that sells electronic parts Radio Shack or better)....
Chosen Solution Good Morning, I have a 2012 Craftsman ZTL7000 zero turn mower. I just recently bought it and did the first cut today. Everything was going well, until I went from reverse (PTO disengaged) to forward and the PTO didn’t engage again. I was able to get it to re-engage to finish the job, but I had to dis-engage and engage it multiple times for it to finally engage. I also went from reverse to forward multiple times as I thought it might be related to a reverse safety switch....
