Chosen Solution I put my RCA Tablet 7" Android 4.4 KitKat tablet on the charger and it goes to the robot with no command.I have rebooted it a couple of times by pushing the power and volume up&down buttons before and gotten back to the main screen.But this time no luck.It will go to the rca screen then to the robot.I dont think It will charge being on the robot.It will not stay off when i put it on charger....
Chosen Solution The black “roller” which can be seen after opening the back of our printer which is a Brother HL-L835OCDW there is about a half inch of the black ruberish look material missing which is creating a funny discoloration line on everything we print. Is this replaceable and if so who can I call. If that roller is on the toner cartridge, replace the cartridge.
Chosen Solution This fell out while I was replacing the logic board and I didn’t see here it came from. Could anyone tell me where it belongs? That fell from top right of the phone, it’s screwed to camera and logic board, see the pictures at step 20 and 23 of the guide: iPhone 6 Plus Rear Facing Camera Replacement
Chosen Solution Thank you, I have a question: Where can I buy that battery? Could you send me the battery specifications please? Hi Guillermo, the Capacity is: 415mAh/1.6Wh and cut-off voltage 4.4V. The size is about 28.3 mm wide and 26.6 mm in height. I added a close up of the battery and hope it helps to find one.
Chosen Solution my playbook wont turn on but when i plug it in it stayed on red light for a few second then turned green and blinked 5 times eman, the most common reason for that is because the battery is completely drained out, discharged below the charging threshold. The problem with the playbook is that it will not charge, if it is drained past that point. Try these solutions:" Solution: try these 3 different step by step solutions....
Chosen Solution Redmi note 4 charging issue : 1.It is not continuously charging …….after 5 min or in few min it will automatically charging stopped….after i re plugged its charging ..and again same issue. one day its charging up to 3%. fullday it connected battery indication is glowing but at the end same 3% what is the issue any suggestion vradhakrishnan25@gmail.com please help me i tried many things: I replaced new battery…....
Chosen Solution I’ve recently installed a new battery, everything seemingly flawless. But upon start up I noticed that the device does not register the battery, checked connections, all good. PRAM reset done, SMC reset done. NOTHING! am I missing something? thanks! Ouch! Not good ;-{ You have a bad battery, contact the seller to get a replacement.
Chosen Solution Hi all, So spent some time hunting and cant seem to find a definitive answer. So just replaced an iPhone 8 screen, phone boots normally and with normal brightness, then after approx 10 secs the brightness falls and can just about make out the screen contents. Brightness settings are still on full when this happens so cannot increase brightness. Re-installed the original screen and no issue at all works perfectly....
Chosen Solution The original battery was thrown out by mistake which had the 3 way male adapter. An article states that you can use two 3.7V batteries. The connection to the original battery has 3 wires, red, white and black. Can you explain how the 3 wires should connect to the two 3.7V batteries? I am an electronics engineer. Hi, The battery shown at Step 6 in the Ifixit battery replacement guide for the player here....
Chosen Solution My original trackpad failed so I ordered a new one from iFixit. It responds normally to touch but won’t “click” when I’m trying to select something. I’ve adjusted the T5 screw up and down where it connects to create the “click” but to no avail. No idea what else to do and it’s driving me crazy. Make sure you got the correct trackpad and the frame is not bent from a swelled battery....
Chosen Solution Although it seems to be quite rare, this iphones backlight sometimes doesn’t turn on or even stops working while using the phone. A few momenta after it starts working again or if doesn’t, it will come on with a restart. I took it apart, but nothing seemed to be damaged. The phones camera also turned black on me with the flash not working (saying it needed to cool down)....
Chosen Solution I am having problems with a sim card reading in this phone, the copper feet seem fine and there is no liquid damage, however the sim reader is only intermittently reading the sim. I am wondering if it could be due to the part circled in the picture, and if so what does it do? Thanks! The red circle shows the SIM Tray detector. The SIM Tray when inserted all the way pushes that copper bar down, breaking the connection on the left side of the SIM bay area in your Red Circle....
Chosen Solution I recently replaced the battery on my 15" Mid 2012 RMBP. I’d installed a clean version of High Sierra before installing the battery. Since replacing the battery, the performance fo the Mac feels a but sluggish, glitchy almost. Here’s what I did: Tried resetting the SMC - which didn’t seem to even work properly. The light on the power cord didn’t blink to indicate anything had happened. Startup progress bar also seems to stall for a noticeable 5-10 seconds now, about 3/4 of the way through....
Chosen Solution I cleaned the keyboard of my samsung laptop with foam spray, then some keys become not work. How I can solve the problem? Hi, Here is a link to a video which shows how to remove and replace the keys on your laptop. Just do one at first, to see, with the key removed, what is causing the problem. https://www.youtube.com/watch?v=1It2pfKG…
Chosen Solution I have an iPhone 7, sometimes randomly my speakers wont work. For example my phone would not make a noise when a message comes in and it will only vibrate. If i try to watch a video then there is no sound. When this happens I restart my phone and then it works again. What can I do to make this not happen? The iPhone 7 series of devices have proven to be very unreliable, suffering from flex-based issues similar to the iPhone 6 Plus (Touch Disease)....
Chosen Solution hi friends! I’ve been given a laptop to repair (it’s my first one ever…so feeling a little nervous) it’s quite a simple fix by the sounds of it but there are always little surprises aren’t there? One of the pins on the DC in port has broken off. So 1) any special advice regarding laptop repairs in general 2) how similar are these models? can I use pcg-xx as a guide?...
Chosen Solution Hello Mike, thank you for the answer. My problem was error 29 at my 3GS 32GB Serial 88018H693NR, Model MC133T/B, BB 05.15.04-6.4_M3S2, FW 4.2.1 because of a old batterie. I have ordered a new battery in Germany with the number 435th. However, I was mistakenly delivered a 431. But I tried it and this work… I was able to recover the device with itunes. But now I have another Problem with the LCD-Display-connector....
Chosen Solution Hi everyone, I have a brand new 2015 13" MacBook Pro which replaced my damaged 2014 unit but the new laptop came with a german keyboard. I would like to swap the whole keyboards(as swapping buttons one by one seem to break them sometimes). I have already swapped my ssd drives (new one came with 128GB and I had a 256GB from the old machine) and noticed a slight difference in the cabling around the trackpads but did not look for differences in the keyboards....
Chosen Solution I was working on a MacBook Pro today that is shutting down probably due to overheating. I passed my hand over the board to try to find the heat source. I realized that this just wouldn’t cut it. I watch Alton Brown on the Food Network a lot and he always has great new tools. One is a Laser thermometer and you just point it at something to get a temperature reading....
Chosen Solution Hi Everyone.. Hi @refectio Sir.. I have a question just for general knowledge. Sometimes we have a phone for repairing, but dont have a Power Supply cable with right Battery connector. Suppose this ipad mini 1. If i want to power the board, how can i connect the power supply red and white cable? Black one is Ground But this connector have more then 1 Rails on battery connector : BATT_SWi_CONN BATT POS CONN BATTERY NTC So where can i solder the RED Wire for give a Power to Board… Thanks...
