Posts

Chosen Solution where is the location the radiator drain on 2500 6.0 Silverado? The radiator drain plug is located at the bottom of the radiator tank passenger side facing engine on my chevy silverado. Word of caution let vehicle cool before attempting to drain coolant, and consider draining by disconnecting the lower hose as quite often the draincock becomes damaged and will not reseat properly and leaks. Good luck. I hope this helped you out, if so let me know by pressing the helpful button....

Chosen Solution I bought my iPhone 3G second-hand by a friend that had ‘dropped it in water’ (didn’t say how much water). So now the power switch is ‘acting funny’ (most of the time not working at all). I’ve taken the iPhone apart and the switch ’looks ok’. I don’t know what to call/describe the switch, but it’s in two (three including the externaly visable part) pieces. The ‘main [electrical] body’, and a small, oval (‘half spherical’?...

Chosen Solution How do I know which MacBook Pro 15” 2014 I have? Retina, Unibody etc. I need to replace the internal battery Here’s the needed part MacBook Pro 15" Retina (Late 2013-Mid 2014) Battery and here’s the guide MacBook Pro 15" Retina Display Mid 2014 Battery Replacement

Chosen Solution I replaced the damaged LCD display with one from iFIxit but when I turn on the iPod it shows nothing on the display. The backlight works; I can hear the drive spinning; and I can play songs but no menu or song info shows on the display. I’m going to try retracing my steps and making sure that all connectors are on solid. Any suggestions? Toggle the Hold switch on and off....

Chosen Solution Hi there! Does anybody know if I could replace the lcd screen of a 15" G4 Powerbook 1.67 GHz with one out of a 15" titanium powerbook? Many thanks Sascha Scoot Head, if you check these two links you’ll find a reference for the Titanium LCD: AU Optics Corporation - PN B152W01 (works in all Titanium models). Looking at the other link, the same B152W01 is advertised for the PowerBook aluminum....

Chosen Solution Roomba 960 making noise after side brush replacement. Take it out and follow the guide on replacing it. Look for any broken parts: iRobot Roomba 960 Side-Brush Replacement Roomba 960 side brush was making a click click noise. Motor working fine. I took the brush off and a little WD-40 sprayed inside and brush put back on. Solution was a simple fix and wanted to share in case it helps....

Chosen Solution OK we’re on a pretty steep learning curve here, Dan. I just need to check a few things with you before I go further. I didn’t look at the Dual Drive instructions initially as I thought that referred to the Hybrid drive mentioned in an earlier post. I’ve now read it and am happy to continue. I’ve checked the Hard drive enclosure at step 22 and intend to order part EU107081 in EU ifixit store or IF107-081-1 in US store (at half EU price!...

Chosen Solution Is the internal power supply a 120VAC to 12VDC like its predecessor? jeffkomori yes it is. It is a 150W power supply that runs off 100-240 VAC at 50 to 60 Hz and internal components are 12V Hold on there! We really don’t know much about these machines yet because iFixit has not gotten to tear one of them down yet. You are better off waiting for the teardown, your question will probably be answered when it happens....

Chosen Solution My Samsung Flex Washer Door is locked. Wash cycle completed and i drained the water from the washer but the door will still not unlock. How can I unlock to get my laundry out. Hi @skbgirl , Have you tried disconnecting the power from the washer for 5 minutes and then reconnecting and checking if the door can be opened? Just a thought. Don’t know your model but have found the service manual which as far as how to manually open the door is not helpful....

Chosen Solution Laptop was droped from short distance and screen cracked and im looking for a way to order a new screen and the company is not really helping me in this Hello, IT Pro here… Screens can be bought from a verity of different places! You can search from them all across different websites. The most reliable place though would be though the same company that manufactured your laptop. However, not all manufacturers will sell their parts....

Chosen Solution the Phone sometimes fail at the start just after the boot , sometimes waits a minute after it boots and does it here’s a video of what happens : https://www.youtube.com/watch?v=Sa9tO3Bj… sometimes it give other colors like green and grey and shows flickering lines I tried screen changing and software flashing but no luck what would that be? I found what’s it it’s because of low electricity so if it happens to you do one of the following :- -lazy solution , keep it in charger all time...

Chosen Solution I’ve been looking everywhere for a screen replacement for this phone. I’ve cracked my screen. Where can I buy a replacement display? Hi @alvinhunt Try searching for SM-A115F LCD display (supplier example only) to find suppliers that suit you. I think that this is the correct model number for the phone. Check your phone’s model number to be sure and if it is different, search using your phone’s model number rather than just searching for a display using the Samsung phone model name....

Chosen Solution HI have a a strange situation with a A1989, had to replace the battery on the unit. After battery replacement battery show “service battery” on Monterey 12.4. It only does this on Monterey, Catalina 10.15.6 and Big Sur does not show this message. The battery charges and holds charge with no issue. Tried 3 new batteries and same result. Steps taken: SMC+NVRAM reset Full DFU restore. archive install updating from a known working OS....

Chosen Solution Looking to troubleshoot what is wrong with my Sharp lc-42sb45u thinking it may be the inverter board @randyy123 that sounds like a power board issue possibly an inverter issue. You do want to go ahead and check a few things first. Something like this: Is BD901 (+320V) output? (Set the main power SW to OFF.) (LED) When power on/off switch is on ‧‧‧ About +400V Is a voltage of +5V applied to pin (11,12) of connector (CN902)?...

Chosen Solution sim and sd card tray is half broken inside my phone and it won’t come out Need help!! Honestly for this one I would just take it to a phone repair place. It’s not hard to fix, but you risk breaking something that isn’t easy to fix. If you feel like rolling the dice, you can just follow a disassembly video on youtube and open the phone up and stick a needle in the SIM/SD slot to fish it out....

Chosen Solution A while ago, I removed the sim card form my Iphone. Today I decided to reset it. When I did, it said I must put a sim card in the device. But when I did, it didnt show up. So, I tried to eject it. I can get the tray to pp put, but not all the way out. I do not want to take the back off my phone....

Chosen Solution Hey Guys, Can anyone tell me the size (length) of this screw? cant find it on any of the iphone 8 or iphone 8+ guides and its a standoff screw on the iphone 7 so not really sure cheers Heres a full position map of the screws for an iphone 8 i made Housing: Print Screen: a4-screen the screw sizes in the guide are horribly wrong and will likely cause short circuits if followed....

Chosen Solution Some of the small components of the logic board of an iPhone 4S are gone. It gives problems during charging. They are pointed with an arrow on the picture. What are those? Can I solve this problem by bridge the contact points? Thanks in advance. Gauthier Top, I marked the components in numerical order. They are a follows. C293 100PF 5% 16 V NP0-C0G Capacitor R153 0.00 0% 1/32W Resistor part of BATTERY_NTC circuit R61 0....

Chosen Solution Macbook 4.1 13" 2008 White - MacBook “Core 2 Duo” 2.1 or 2.4 GHz I’m upgrading my original MacBook HD from 128GB to 500GB. How and when do I back up and then restore my current hard drive. Do I need to format the new disc and do I need partitions and if so, how do I do that. Thanks, Mikie Yes - you should backup - Ideally you always keep a current backup....

Chosen Solution My Amana Model # SQD26VW stopped cooling about 6 weeks ago. I unplugged it, cleaned the coils under the fridge and around the fan located at the bottom rear. Two days later I plugged it up and it cooled fine for a couple of weeks and then quit cooling completely. I have checked the coils in the freezer, and the compressor seems to be running ( I hear a faint humming noise coming from the compressor ) please help!...