Chosen Solution I have the Xenyx 502 mixer. I am trying to set it up. I have an xlr mic going in. I am getting almost no sound in my headphones. When I turn the main mix up past about 40% I get a high-frequency sound. As I continue to turn it up the frequency of the sound gets lower and lower. Any thoughts on what this might be? Hi, Is the mic the only input connected when this happens?...
Chosen Solution why is there no answer for this question? I have the same problem resetting it with the pin in the back doesn’t even work. can we get an answer? Barry Martin sounds like you have an issue with the operating system. Try to Boot into recovery mode by pressing and holding the volume up and power buttons. Once the RCA screen (the one with the dogs :-) comes on, let go of the volume up button and you should see an android image....
Chosen Solution Hi, my imac does not start mac os and shows a temperature of -127°C at the sensors TC0D and TC0P under Linux. i have already measured the sensor with a multimeter and it seems to be ok. Maybe someone can help me to find the cause. Thanks a lot :) A negative value like what you are seeing is either, an unused sensor input, a bad sensor or the connection pathway is broken to the sensors input within the SMC logic....
Chosen Solution Hey all. I recently came into possession of a water damaged macbook. It was my cousins and he gave it to me to either try and fix or sell for parts. How do you guys go about testing the components to see what is salvageable and what is not? I have a macbook pro, would any of the parts be testable in there? Im thinking maybe the memory and hard drive would be easiest....
Chosen Solution Why doesn’t the DVD draw open? @gembka ,Tim, if newer and under warranty and none of the listed fixes work, return device for repair/replacement/refund. Try resetting the player, shut off player, unplug for a minute, plug back in and try. Found some more procedures below from Sony forum for you to try, check the link below. Good luck. If out of warranty and none of the procedures worked, you may have to remove outer case and see if DVD is jamming the drawer from operating, I hope this helped you out, if so let me know by pressing the helpful button and tell us which button combination worked for you....
Chosen Solution The sound on the Kurio 7s won’t work. At the top there is speaker with a slash through it. How do i fix it? Update (10/21/2017) there is a picture. Hi @marykiera , It may be that a hard reset (or factory restore as it is also known) may resolve the problem for you. Be aware though that a hard reset will erase all your downloaded apps and user data....
Chosen Solution Good day Have a very interesting issue for today, recently did a time machine backup of a 256GB 2019 TB MacBook Pro 15", the data on the machine was 128GB. Backed up to a 256GB ssd, back up went trough perfectly with no issue. Formatted the machines drive and loaded a fresh OS, this is where the issue comes in as I can’t put the back up back as it is to large for the machine....
Chosen Solution I have heard of one of these A1347’s having 10 GB of Ram installed; how is this possible? This system has two RAM slots which supports 2, 4 or 8 GB modules. You can mix them so in this case the person put in a 8 GB & 2 GB = 10 GB. Not sure why they did this? Most people just put in two of the same sized modules so here two 8 GB would have given them 16 GB of RAM which is the limit for this system....
Chosen Solution Hello, at the moment I am trying to get into the topic of board repairs but I got a little problem in troubleshooting the board of iPhones. I watched guides and explanations on which parts a board consists of and what every part does (rails, resistors, capacitors etc.). After that I looked for videos on how to start troubleshooting logic boards but I only found videos about troubleshooting boards from laptops....
Chosen Solution My 9 year old daughter has a p4 computer and it runs slow and freezes a lot. I need to reformat it to reinstall windows but forgot how to do it. Is there anyone that can give me a walkthrough? 1 This section explains how to reformat a drive from the Windows XP installation CD. This can be used when installing a fresh copy of Windows onto a computer....
Chosen Solution So I’m wondering if there is an easier way to remove the black adhesive glueing down some components on all iPhones, IPads, etc. that doesn’t involve scraping and possible damage to other components or solder pads. I’m not expecting miracles, but is there possibly a solvent or process that would be a safer, faster or easier choice? i dont think there is any solvent remover for underfill yet. it just looks like scraping is the only option atm
Chosen Solution So i just replaced my screen, and it was working fine for like 2 days, then suddenly the backlight is dead. i didnt disconnect the battery when i did it, but it seemed to work for a few days after and just died while i was driving home anyway, i’ve repaired this phone a number of times (battery, headphone jack x2, screen x1) and i would like to repair it one more time;...
Chosen Solution I would like to konw how much does the conector port to 120gb iPod classic cost. Through iFixit it will cost $99.95 for the board that has the connector port on it. See link iPod Classic (80 GB and 160 GB Thick) Logic Board Then follow the instructions to install.
Chosen Solution Hi! I replaced display assembly on my phone last night (ifixit rocks). Everything seems to be good except the phone speaker no longer works–I can only hear calls if I put them on speaker phone. Any Ideas? I suspect that maybe I didn’t get the digitizer cable installed correctly… though I’m pretty sure I did. Perhaps the display I got is defective? Anyone else have this issue? Sounds like the logic is not properly seated with the ear speaker prongs making contact on the board....
Chosen Solution I had a customer come to me with his iPhone 5s that was having problems charging. He had replaced the battery on his own before coming to me. I ordered a new, unused lightning port assembly from a local shop on eBay and installed it. Now it won’t power on at all. Could this be a matter of reseating everything to get it to power up? My fear is that it’s a chip on the motherboard that’s fried....
Chosen Solution Hello, I’ve got an iPhone 3GS and recently replaced the LCD assembly. I’ve bought the assembly from eBay. The first one I received had a problem with the ear speaker. The volume is very soft and i can barely hear the caller. My question is: Could this be a problem with the earpiece itself or the proximity ribbon cable? I’ve bought more LCd assemblies (also for iPhone 3G) and those were also very soft....
Chosen Solution Received new HD 3TB Seagate; had it formated for mac and partitioned prior to installing. Cleaned inside this mac: heavy smoker. Loaded new HD, reassembled, booted, OXS 10 loaded, then Snow leporard, the basics. Now confused: how to clone from time machine to new 3tb hard drive. Not paying for all new programs; word, office ect. which I already paid for . Just want to bring new hd to system already in time machine....
Chosen Solution I want to know if I need to replace the whole LCD or if I can replace an Inverter or a different display component or possibly do some cleaning. I have some photos of the broken mac next to a fully functional mac as well as some pics of the back side of the screen. I know that I probably need to replace the LCD but I am trying to stay cheap....
Chosen Solution After applying new thermal paste to my Xbox due to overheating , it now stays on but I have a new problem . Now no picture is on the screen . There is still sound and the tv is connected to Xbox but no Picture. Is there something i forgot to plug back in after re assemblage? the HDMI port is directly attached to the mother board, so either a board component fried out/got damaged, or the HDMI port got damaged, and needs replacing....
Chosen Solution hey I just recently bought a new note 10.1 and wanted to insert my macro sim with adaptor so i can use my inlimited data on tablet .But as i removed the sim after small pieces of metal came out as well and now i need to replace the sim card tray and i cant find any directions or manuals how i will do it You will need to replace your SIM card tray....
