Chosen Solution My PSP 2006 is unable to detect the battery (both newly replaced and old battery). When the psp is running on the ac supply with the battery in it (power indicator doesn’t light up), the battery information shows no percentage or other battery info but shows that power source is on external. May I know is there any solution to solve this issue? Or my psp is ready to go?...
Chosen Solution Hey, i had had a water damage Macbook come in for repair. I took the LCD Connector off because I noticed it was burnt on the right side of the logic board. anyways, I pulled the connector off and noticed a pad was gone. I looked at the trace for it and it looks like the last pin is on the same circuit. Can some chime in to tell me if I could solder the pin over to that one?...
Chosen Solution power light red while charged The red battery light basically means that there is an issue with your alternator, your battery, or some other part of the charging system which could be as minor as cabling or as major as a computer malfunction. You can simply try with another charger and see how’s everything going.
Chosen Solution My GE Refrigerator works now. It had been acting up. That is in the top(Freezer part). The bottom part which is the refrigerator is more like lukewarm. I can’t keep milk or anything in it There is a ice buildup underneath the freezer on each end of the bottom of it. The refrigerator is warm and the freezer is cold. What can I check? Hi, What is the model number of the refrigerator?...
Chosen Solution I have Acer monitor which was working perfectly. Then my cousin got confused with the wire and powered the monitor with cable which has 12 V AC as a supply. That power cable is used for woofers. Since the pin look alike he inserted it. Now even If i insert the preferred power cable it’s not turning on. Please help me with this. What might be affected ? If it is possible to repair it by myself please let me know :) Thank you...
Chosen Solution I used an OEM part to replace the lightning port in my iPhone 6, which now will work and charge my phone. However, after resetting my network settings and even trying a different part. The antenna/microphone will not work. The calls drop or the receiver of the call cannot hear me (I can hear them). I am constantly having to go into Airplane mode to get back on LTE....
Chosen Solution I have a iPhone 5c that spend 2 weeks in a muddy sump. Build a grabber and it come out covered in mud. Put it in rice for a week. Charged the battery, but the screen wouldn’t light up. Ordered a new full every thing there screen. While waiting for the screen to come in, I hooked it up the charger and it came alive, but no screen. I got a message on my iPad that Dons-iPhone is using my ID for messaging and FaceTime....
Chosen Solution My Firewire port seems to be dying. Where am I missing the guide that details repair or replacement for this problem? Sadly, your only option here is to replace the complete logic board following this IFIXIT guide: MacBook Pro 17" Unibody Logic Board Replacement. If you know of someone who is skilled in SMT soldering you might be able to replace the socket alone if that is the problem....
Chosen Solution I have the replacement parts, but need some information in replacing the old one. Simply pull off the rubber cover, using a flat screw driver to help if needed. You will then see a bolt that holds the assembly in place, and a few screws that hold on wires. Remove those, and then unplug the wire harness plug. With all that done you should be able to pull out the old switch....
Chosen Solution Hello. So i get this iPhone 7 on my desk, with water damage, very light corrosion here and there, cleaned and replaced the caps who seemed damaged, now the phone charges normaly (~1A on a 1A charger). The iPhone turns on and after ~5 second resets itself, so i thought i might be the iOS that is the problem, so i restored with iTunes to latest version, all went well no errors the screen was lit the entire time with the Apple logo and the progress bar....
Chosen Solution A few weeks ago I noticed rose spots on the left side of the display. Aggiorna (25/04/2018) Here a photo of the display Okay what you are seeing are pressure mark spots which can be caused by many things: Replacement screen put on too tightly. Battery expanding resulting in increased pressure of the battery against the screen and back cover. If it’s the battery expanding the battery would need to be replaced....
Chosen Solution My samsung gear watch will not take a charge, don’t know wether it’s the charger or the watch. I don’t think it is the watch because it was working fine when it was charged. How much are the charges? Same issue…my charging contacts on the back of the watch were worn away. From another thread I learned about the Circuit Writer, a pen that dispenses conducting ink. A drop on each contact and my watch charged again, and the pen was only about $12....
Chosen Solution Is possible to tighten the iMac screen hinge without completely dismantling the computer. some claim a plastic card pushed in above hinge with release a clip allowing asscess to torx screws ? Simple solution: A rubber crutch tip placed between the monitor and the stand holds the monitor position securely and can be very easily adjusted in about 5 seconds. Cost: $0.29. The newer iMacs have a newer foot design....
Chosen Solution I am trying to replace the battery on an apple watch original. When I follow the directions here: Apple Watch Battery Replacement I have 2 extra cables on the side opposite the crown and power button. I do not see those in the guide. What are they for? How do I get around them. I figured it out. It was the haptic touch connectors It is an SP1...
Chosen Solution Will the lcd work if i swipe it? No reaction on the ipad. Unsure if its a new lcd ir glass that i need I believe you asked this question yesterday. The LCD is just for displaying the image, avoid touching it as it can be hard to clean (a lenspen works well) and scratches easily. The touch capability is provided by the digitizer (front glass). If you are having issues with touch, either your replacement digitizer is defective or you damaged the flex/connectors....
Chosen Solution hi my zanussi washing machine is displaying e60 and wont work any ideas The error code E60 on a zanussi washing machine is a motor issue. First try resetting the machine by unplugging for five minutes, Next check to see if the wires are fully plugged into the machine motor. a little more specific please. AM I to dismantle the machine’s body and look into the connection to the motor to see if any leads have come undone thank you
Chosen Solution I am troubleshooting a Sony KDL-75W850C per the service manual. 6 red blinks indicates either bad power board or LD panel. I have checked power board and I have good 3.3v STBY, 12V, and BL_ON. . It says I need to measure the LED output voltages. I assume I measure them between OUT+ and OUT- on the board. All the other points are measured to Ground. The reason I ask is I get a brief pulse of 132V between OUT+ and OUT- then it collapses to 0....
Chosen Solution I’ve been playing a lot of YouTube videos recently which has caused the fan to whir a lot more than usual. Then I noticed the audio on my earbuds quit, and when I tried to adjust the volume on the keyboard controls the onscreen sound display had a line through it (the “no” diagonal line) and I could not adjust sound. Now, when I first turn the computer on, sound and video work fine for a while, but after a while of use, the audio quits....
Chosen Solution When braking from speeds over 50 mph, typically under light braking such as slowing down for a stoplight, the steering wheel shakes back and forth from side to side. If it is the steering wheel shaking, it is most likely a front brake issue. You can often visually see through the wheels to see the pads, but there may not be much you can see. A shaking usuaully indicates an out of round or thickness variation condition with the rotors....
Chosen Solution This laptop experienced water damage and I was able to clean it all up. The laptop works fine except there is no backlight on the screen. I have replaced the LVDS connector because a couple pins were completely fried on the old connector and there is still no backlight. There is a slight hole in the motherboard next to a few of the pins that I assume are not making connection due to the hole....
