Posts

Chosen Solution Why is my player turning itself on then off, on then off though we are not currently using it or trying to use it? Preforming a hard reset will help https://www.youtube.com/watch?v=o4gV4v_b… Well, you are in luck: I have finally found out how to fix it. The issue is that the touch screen panel has failed, and thus causes the Blu Ray Player to cycle on and off. (1) Unplug Samsung Blu Ray player; (2) Remove sidewalls and top cover; (3) Remove front fascia; (4) Remove front touch screen board by rotating the top out first, then you will see a thin brownish ribbon attached to the bottom; (5) Disconnect brownish-colored ribbon from the rest of the system by pulling it straight out (the brownish ribbon runs up to the touch panel buttons); (6) Re-assemble, leaving touch screen panel brownish ribbon disconnected from the rest of the system....

Chosen Solution I have to go to airport mode and completely shut my tab off . If not a samsung commercial turns it back on Try holding the power button for about thirty seconds.

Chosen Solution My Sony Bravia KDL-37L4000 started displaying the picture, in what looks like a negative image. what should be light colors are dark and the dark are light colors. It had been working well and just happened when i turned on the TV. I am wondering if the tv is worth the cost, to try and have it repaired. morkleb77 sound slike you are looking at solarization. You do want to go ahead and post some images of what your screen shows with your question....

Chosen Solution Hi all, I’ve facing screen flashing problem last few week. I’ve tried SMC & NVRAM reset. But not work for me. Screen still flickering/flashing. I’ve also format my Macbook and install fresh copy of macOS High Sierra. Yesterday, I’ve update macOS Mojave. Still facing flickering/flashing problem. Note: When I’ve moving the cursor “screen doesn’t flickering/flashing”. Also If I’ve play any video(only) in any player or play youtube video “screen doesn’t flickering/flashing”....

Chosen Solution Just replaced the battery on my iPhone SE. After finishing the the repair the screen was occasionally freezing and registering phantom touches. I tried reseting with the home and power button with no luck. Disassembled blew off the connectors with canned air then reassembled. Now the problem is worse. Any ideas how I can fix the problem? This was my first phone repair so I tried to be as careful as I could and was sure to make sure all the screws went in the correct places....

Chosen Solution I have read lot’s of threads on this site about this problem. I didn’t find the solution to my specific situation. At first this problem was random. Now it’s consistent so I can’t boot up. At first I thought that this was a software issue so I did a clean install of Sierra. Problem: Chime sounds on startupScreen stays black I have tried resetting the PRAM. This seemed to help a few times....

Chosen Solution I recently changed the oil in my mower. Since then it runs normally for about 5-7 minutes then white smoke starts pouring out the exhaust. Any ideas? @toro you did check the oil level to make sure you did not overfill it. You did not tilt it over while you were doing the oil change, this could lead to oil in the combustion chamber. It will help if you let us know what model your Toro is and what engine model you have....

Chosen Solution Hi, I recently purchased some tools from you to replace my macs dc connector. Everything went ok, but I have lost the audio. Can you tell me which connector to check to make sure I plugged it in good? Thanks I would attempt to reset the PRAM (hold command + option + P + R while powering on until you’ve heard it chime twice). If that didn’t work I would reset the SMC Make sure your Mac is connected to power and turned offPress and hold the left Shift + Control + Option buttons while pressing the power button for 5 secondsLet go of all the keys & buttonAttempt to power on after waiting 2-3 seconds If it still had no sound then I would check the subwoofer cable and the left speaker cable Hopefully one of those steps fixes it for you!...

Chosen Solution My Iphone 3gs had water spilled on it and has been sitting for a few hrs and went dead . I took it apart and placed the screen and logic board in a bag of rice for a week or two . I notice the battery was corroded so i replaced it and put all back togather . Turn the phone on and everything seems to work fine and bout a min into it the screen went really Dim and it stays that way unless i let it sit for abit not being lite up, and it will work again, then starts to go dim again ....

Chosen Solution Hi! I have an iPhone 6s which I did an NFC repair on. Previously, it was working 100% and looked okay although the water stickers were red. Afterwards, the phone had a shorted pp1v8sdram cap which I removed. The cap was opposite the site so I assumed it got too hot and died. There was some solder ball squeezing on the opposite side but not much. The phone worked for about two hours, except for the flash....

Chosen Solution Basically I’ve bought a 2012 logic board on ebay for a bargain and its a way higher spec than the macbook pro i previously fixed. Anyway according to ifixit guides and wikipedia basically besides the logic boards, the 2011 and 2012 a1286 models are no different components wise. So therefore can I buy a 2011 macbook pro thats broken and put it in? Reason being is on ebay they are significantly cheaper....

Chosen Solution I have two 17-inch Macbook Pros, and I want to swap the screens. One Matte 17-inch mid 2010 and one Glossy 17-inch late 2011. Is this possible? Thanks As you can see the complete lid assembles are different part numbers. Trying to replace the LCD its self could be done but in the process you’ll likely damage the rubber gasket or the cover glass. Here’s the IFIXIT guide: MacBook Pro 17" Unibody LCD Replacement....

Chosen Solution I’m replacing the heat sink and thermal sensors in my A1260. Per product information, " The cable on the left thermal sensor is shorter than the cable on the middle thermal sensor and slightly longer than that of the right thermal sensor." Being that this indicates the middle sensor is the longest, would there be problems purchasing 3 Middle sensors to replace all three? Currently, only the middle sensor is available on the ifixit parts store....

Chosen Solution Have a Kenmore 500 series. A few days ago we started with another problem and the spin cycle would not work but everything else did. Replaced the clutch and rebuilt the transmission and the spin cycle worked for a few quick tests. Was excited. Then did a load of laundry and completely different problem now. The timer just makes a clicking sound on any position other than fill and the motor doesnt even try to start....

Chosen Solution Hey guys, I couldn’t find answers anywhere else so this is my last chance. I have had my Galaxy S6 for about 3 years and have never damaged it previously. Its battery isn’t very good anymore, but it worked fine - up until I dropped it facedown on a tile floor when the charger got stuck on my chair wheel. The display (mostly) works fine; sometimes it jolts while rebooting or randomly shuts off and refuses to be turned on again for hours....

Chosen Solution I moved recently to a brand new flat and it worked like a charm for the past 2 months when I connect it to the internet through Wi-Fi. Now it simply crashes within 10 minutes of connecting it to Wi-Fi. Ethernet remains functional though. The TV screen just goes all of a sudden blank and no light is visible on the actual console when the fault occurs. When I press the power button on the PS4 it beeps but nothing happens (no light also shows up)....

Chosen Solution Radio buttons on steering wheel that allow you to change from one station to another work when car is simply turned on (engine not running), but don’t work when engine is turned on. (Can’t change from one preset station to another). Volume control works both ways and all other functions work just fine (touch screen, control knobs) in both situations. 2016 Nissan Rogue Check to see what is displaying in the center display on the dashboard between the tach and speedometer....

Chosen Solution The GPU of my MacBook Pro (17-inch, Early 2011) crashed, leaving the it unable to boot after hanging on a screen with green vertical stripes. Apparently a lot of MacBooks from 2011 share suffer from this (https://www.change.org/p/timothy-d-cook-…) I was wondering, since the entire logic board needs to be replaced, if it can be replaced with the logic board of the Late 2011 series. It’s only a minor upgrade of the CPU and GPU: Early 2011 Late 2011 Processor Number: I7-2720QM I7-2760QM Processor Speed: 2....

Chosen Solution The short version: After replacing my battery on an iPod 5G/Video (30Gb) which had a possible logicboard fault too the iPod is now completely dead. (EDITED, originally the line mistakenly said not completely dead) The detailed version: I’ve a 30Gb 5th gen iPod. I got it as a slightly faulty hand-me-down from my brother when he upgraded; the problems were: a short battery life (5 or 6 hours of music without using the equaliser)nothing audible in the right earphone when using the 3....

Chosen Solution So I replaced the whole assembly on my MacBook Pro “12, now the computer will not power on at all. No indication of charging, I didn’t use the battery disconnecter tool that ifixit sells. Any help would be grateful thank you in advance If you did not press the yellow button next to the battery before removing the trackpad cable, and you didn’t disconnect the battery in some way, there is a high chance you have damaged the logic board....