Posts

Chosen Solution As said, I did my normal start up, and there was an immediate loud clicking noise, along with a whirring sound I guess? It was loud and scary enough that I shut her back down (properly) and have kept it off since. I contacted apple, went to two geek squad locations, and two computer places that I guess are apple-certified? The guy with apple recommended them because of my laptop’s age....

Chosen Solution The screen (Apple logo and slider bar) upon startup are often ‘grainy/pixelated’ and more often than not system will reboot on it’s own. Eventually it will boot and all runs well, screen, wifi, bluetooth, internal keyboard/touchpad, etc.. Left fan I know needs replacing as most times it’s not running. My concern it the startup attempts/behaviour. Am I looking at a logic board issue (video chipset on the way out)?...

Chosen Solution Do you supply the sticky backing for the battery? When I ordered the tools and battery it came with it but now I ordered just the battery and it’s…well…just the battery. If not where do I purchase the sticky stuff? Thanks, Javier Hello, I am not sure if the ifixit kits come with the battery adv=hesive but if it doesn’t they are fairly inexpensive and easily bought from eBay....

Chosen Solution will NOT store numbers crita1960peace , I do not own this phone. Find below, manual for your ZTE. Call log will normally be found on your Apps list or you can also go to your Dialer and find Logs or Call Logs, you may have to change settings/ may have it turned off. Good luck. I hope this helped you out, if so let me know by pressing the helpful button....

Chosen Solution Recently my mac mini will not boot up. The mini gets stuck at the grey start up screen with the apple logo. I tried to boot from OSX install disc no success. I tried pretty much everything but to no avail. I have unplugged it, tried to reset it, no success. I ran the hardware test which I could start and it came back ok. I started the mini in target mode and was able to use its hard drive to boot and start another mini ....

Chosen Solution Last night I left my computer running superduper because it had done about 90GB of 250GB. But when I came down this morning the screen had the force eject window up as well as superduper telling me the it had to stop copying because the drive had been ejected. None of the information on my harddrive has been lost but the drive I’m planning on installing no longer appears when plugged in....

Chosen Solution My drill bit is stuck in my Ridgid R86034 impact driver and won’t eject or pull out even when I pull the sleeve forward. Hold the bit with pliers, reverse the gun for couple of times, and then try to pull it out. Might’ve just gotten jammed in the hex a little. Spray a bit of WD40 into the bit collet, let it sit for a good hour. This series uses a ball detent to hold the bit....

Chosen Solution When I press the buttons on the display to change the mode or the temperature, they will press down, but they won’t come back up. I have to mash the buttons several times before they will respond. Try wiggling the buttons and see if that helps. For more information, refer to the troubleshooting guide! [ Holmes HEH8031 Troubleshooting|Heater Troubleshooting Page]

Chosen Solution After checking all sensors, changing spark plugs, CO2 sensor, crank pos sensor changing battery and so on, the engine keeps cranking slow and doesn’t start. What is wrong with my car??? tlccuroffice “the engine keeps cranking slow “ this would be caused by the starter. The speed of which it turns during start up is directly related to the rotations (and gears) of the starter. If the sensors are replaced or the battery is removed, the ECU learning is reset....

Chosen Solution itunes wont run cos quicktime failed to initialise. Have uninstalled itunes and quicktime then reinstalled but still get same error message If you are using windows and get this error, go to the following link and follow the instructions and see if it fixes it: http://support.apple.com/kb/TS1875

Chosen Solution Why is the downhill light on the dash lit on? Hi, Have you pressed the Downhill Brake Control switch on the dash to see if the light goes out? The following image is taken from the 2012 Kia Sportage owner manual. (You didn’t state the model year so the switch may be in a different location) (click on image to enlarge for better viewing) If operating and releasing the switch makes no difference and you have traveled faster than 40 m....

Chosen Solution Once I teardown my xbox E360 onsole to check if it is Winchester or Corona but sadly it was Winchester I didn’t know but I just touched on chip and there was some paste in it…so cleaned it up but my E give me rrod after some time I did some research and find out that pasting thermal paste would bring back my console and i did it with a thermal paste and didn’t work to me please help me...

Chosen Solution I have to replace the screen for IPHONE 6 PLUS. Can you show me exactly what I need to buy from ifixit.com? Note: I already have all the tools, I just need the necessary parts. Is it possible to replace the screen AND keep functionality of TOUCH ID working? So many places I read about this issue and they always says “careful, you may loose functionality of TOUCH ID forever”....

Chosen Solution Hi all, ran into a weird issue when replacing my screen today. Once powering back on with the new screen connected the phone lights up great, but after being unlocked will cut to a black screen. I tried cleaning the terminals and reconnecting them a few times but it makes no difference. Upon plugging the old screen back in everything works fine. I’ve also hard restarted the phone several times....

Chosen Solution After the second full panel replacement, the glass has again cracked. When attempting to reseat the loose home button glass cracked. First time was due to flex stress at the cable attachments. Seems regardless of how well you follow the instruction that corner does not want to adhere properly. Looks home button was due to this poor adhesion. What is the fix for this.? Why does this seem to be a systemic problem with this replacement panel?...

Chosen Solution I removed the defective charge port from my ipad air the other day. It appears some material from the charge port cable was left on the logic board. Can you confirm this from the below picture? How would I clean this up before soldering the new charge port? https://imgur.com/a/nXKTFs8 It’s hard to say as the picture isn’t clear enough. But typically, you will have some of the pads from the flex “stay” on the logic board....

Chosen Solution Hi all, I’ve been working on a water damaged 2015 Macbook air, following the amazing instructions from Louis Rossman, on YouTube. It’s mostly working, but the SSD is dead. Having looked at the SSD, I can tell a resistor appears to have blown. If you have this SSD, could you please measure it’s value and share it? It would be a lifesaver. Here is a picture of the resistor in question : https://photos....

Chosen Solution The Roomba has been functioning alright.However after getting docked,it is not getting charged.Power supply to the base station is alright.The Roomba is a new one,purchased two months ago. Hi, There is a 12 month manufacturer’s warranty on the device. Since it is only 2 months old, I suggest that you consult the warranty statement that came with the device, as to what you have to do to make a claim for a manufacturer’s warranty repair or replacement....

Chosen Solution Hi all I have a samsung 64inch that blows the safety switch to the house every time try to turn it on. I think it maybe the power board does any one have any suggestions that it could be some thing else. I have also noticed a blown fuse to Hi, Tests to isolate where the problem is. Switch off the wall outlet and powerboard (if it has switches)....

Chosen Solution Hello , I have a problem with my laptop i don’t know what cause this problem and i just wanna know if this a software problem or hardware problem maybe cable or the entire screen is now broken here is the video showing the screen problem Video 1 Video 2 Thanks Hi, Try connecting an external monitor to the laptop and check if its display is OK. If it is then you may have a hardware problem....