Chosen Solution Title says it all. I disassembled and reassembled my iphone and my wifi and gps signal shot straight down. I can barely receive wifi signals sitting right next to my wireless router. My gps signal is the same way as well. Any reasons? Well well my exact problem. I dropped the phone, while i could hear others in normal mode I had some very loud noises during loud speaker call and people could not hear me in either times....
Chosen Solution Hello All.!! I have a serious issue that is plaquing my family. My Ge ( model# GSHS5AKGXBCSS) refrigerator is on the blink. The fridge is not cooling , yet the drawers are ice cold even freezing produce. My freezer temp is also warm. I replaced the start relay for the compressor with no luck. However I don’t think it’s the compressor cause of the drawers. PLEASE HELP!!!! Aaron, i can help if you can answer these questions....
Chosen Solution So I have just replaced my battery on my iphone 6s and when I battery performance it says that it need to be serviced. I was wondering if I got a defective battery or is this normal. I also might have missed a step if there was any firmware change necessary. I would suspect a bad battery first as there are lots of poor quality batteries in the supply chain....
Chosen Solution Is it possible to replace the PS4 power supply fuse?? If it is, whats the fuse amperage?? Thank you very much! Hey mate, I would have thought the warranty would actually cover this fix. But from looking at photos of the PSU for the PS4, it is a soldered on type. So yes it can be replaced, but to do so you will need to de-solder it from the board and re solder a new one on....
Chosen Solution Howdy all! I replace the screen on my 9.7” pro. Broke the home button cable, so I had to wait for a replacement. Got that moved over. Reassembled except for sealing the screen, and everything (other than touchID) worked. Screen seemed to align with the case, so I pulled the tape, and closed it up. Looked good, very happy. The next day the bottom of the screen popped up....
Chosen Solution My iphone 7 plus charging ports messed up so i bought a new one, installed it and now the phone gets stuck at the apple logo boot screen.. I connected the old port and the phone booted up like normal so i reinstalled it and again back to the old problem it doesn’t work and just loaded to the black screen with apple logo and you cant even enter DFU mode… if i disconnect the charging port completely and power on the phone it boots up normal but obviously this wont work for me since i cant charge the battery....
Chosen Solution I just installed a new screen on my Pixel 6 pro and now my front facing camera doesn’t work. It’s showing as all black and when I look at the camera it looks like there’s a film covering it Hi Armando, One thing I’ve been guilty of is failing to remove all of the protective film that comes on a replacement part; it’s easy to overlook and I wanted to slap myself in the forehead when I realized I had to take it all apart again just to peel off a piece of plastic....
Chosen Solution I bought a battery from iFixit and followed the (excellent) replacement instructions on the site, replacing the keyboard while I was at it. I reassembled, and my Mac booted just fine off the battery. I followed the instructions to calibrate the battery: Calibrate your battery before using it: allow it to drain overnight, then charge it to 100% and drain it again until your MacBook Pro shuts down automatically....
Chosen Solution Seeking advice on replacing a capacitor to the compressor in an dehumidifier. The capacitor in question is a CBB61 3 wire 7uF 450V one, made New Tech. It is also rated at 50/60Hz I have searched all over the internet to try to find one which is of the same ratings, with 3 wires to allow for a straight swap, however 3 wire capacitors do not seem that common, especially at the above values....
Chosen Solution Hello! When I was trying to take the screen back off of my watch after removing adhesive and pausing the project for a little while, the screen wouldn’t come off. I stuck a piece of tape to the screen and slowly pulled it off but I must’ve used too much pressure because I ripped what I believe are two copper traces in a flex cable. I’m pretty sure that I need to replace the whole screen assembly now (ouch) but was just curious what exactly I ripped and what they do....
Chosen Solution The roller brush on my Hoover spins fine if you have the head off of the floor, but as soon as you put in on the carpet it stops spinning. I’ve replaced the belt and the same thing happens. I ran it with the head cover off and noticed that the motor stops running when the slightest bit of pressure is put on the roller brush, and then it won’t start up again until you turn the machine off and on again....
Chosen Solution mower runs when the clutch is in,and dies when you release the clutch, why? There is a safety switch under the seat which requires that you be sitting on the mower while it is running unless either the clutch is depressed or the emergency brake is applied. Make sure the wires under the seat have not become disconnected. You may need to test the seat switch with a meter to insure that it is working properly....
Chosen Solution After water damage, finger scanner is not working. Also some lines and rectangular light blue box is appearing which had made portion of the screen unresponsive under it. I am attaching screen shots too. If there is any solution, please do tell me(the most important is removal of the blue box due to which i am not able to press button below it) With water damage, you have to decontaminate the logic board before doing anything else, otherwise there will be latent issues down the road....
Chosen Solution I’m debating on whether this is a dead LCD display or a bad video controller. Since the external display work (VGA adapter to Dell 19"). System Profile does not detect any displays connected, though the external connection does work. I’ve found the video adapter 661-4673 for about $190, and this is definitely the cheaper of the 2 components. A replacement LCD is about 3x that. :( I checked the graphics ROM version and it matches the newer version mentioned in the Apple support doc DL71 Any suggestions on diagnosing this further?...
Chosen Solution So i dropped my phone to water ( in a sink of water ) as soon as i got it out of water immediately. At first , i thought it was fine because the phone just dipped into water only almost 3,4s . After that, i played few games and few minutes later the touching function doesn’t work then i turned off and covered it by rice for few hour....
Chosen Solution I need 20 replacement screws for the backplate to reassemble phone after swapping out screen. Does anyone know the size of these screws and where I can purchase? I have contacted a parts supplier: http://www.cellulardr.com/pages.php?acti… Will have to wait for response from them. Hopefully here. UPDATE REPLY RECIEVED Since we are no longer an authorized motorola repair center, we do not carry screws and are not aware of the size....
Chosen Solution Hi, I have a board which I am using for learning. It does not have any water damage. When I connected it to DCPS for the first time it showed current draw so I assumed it has a short. After checking VCC_MAIN line in diode mode it was confirmed that it has a full short (0000V drop). After injecting 3.8V to VCC_MAIN line i noticed that the Q2300 was heating up....
Chosen Solution Hello, im working on an iphone 6s water damaged that has the VBAT (PP BATT VCC) line taking 90mA when checked with power supply( phone turned off). What can cause this such a small short? I already cleaned it with isopropyl alcohol. Thank you guys! What makes you think it’s short…even a phone that is powered off still draws some current for the “always on” part of the circuit and potentially to charge the battery....
Chosen Solution My trusty 15” MacBook Pro mid 2012 had finally reached roughly 1000 cycles on the battery and was starting to not hold a charge for much longer than 3 hours. I ordered a replacement battery back at the end of March of this year, but then started having strange random problems with my macbook dying during sleep mode and randomly losing the date and taking longer than usual to boot....
Chosen Solution My phone got a little wet and the screen would not slide after to unlock the phone with pass code so I can not back up my phone as the screen will not slide to put pass code in. Phone will power up when plugged into power cable, but home button and power button do not work. Phone will ring and vibrate button works, but just no slide. My phone buddy said that there is a carosian problem on the part of the board were digitizer plugs in....
