Posts

Chosen Solution Hey Guys! My friend has dropped his phone in Turkey and after that he putted it directly in a bag of rise. After 6 days in the bag, it still wont work. I have replaced the Logic Board because i saw on the ‘Power IC’ that it has some burned bubbles coming up like this –> http://i1118.photobucket.com/albums/k614… But after the replacement.. It still not working! I have tested the screen with a test flex cable on a different iphone, and the screen works… Can you help me please?...

Chosen Solution I recently bought a used launch DS and the right button on the dpad is not working. When pushed down it does make a click, however the system does not register it or respond. If I push down hard enough it will either register as an up or a down not a right. I have already tried opening it up and cleaning the contacts but the right button is still not working....

Chosen Solution Hello, Since my Samsung Galaxy A40 wasn’t charging anymore I replaced the battery first (without any change) and then the charger connector, but still not charging. I definitely don’t know why and how it’s possible, any idea? Thank you for your help, Fabrizio don’t worry, when you said you had a usb voltmeter I thought you were a technician or repairer …. usually this type of equipment is not in the possession of “non-industry” people … I have attached photos of the jumper from run to solve the charging problem...

Chosen Solution I have a Wf330anb Samsung washer. It started making as loud whine at the end of the spin cycle. Eventually would not balance with 2 minutes left. Have changed the rear dampeners because the drum looks much lower than it should be. The springs look brand new. Still looks too low. Could the bearings make it look this way? I have pics but do not know how to attach....

Chosen Solution Hello. I changed the charging port and battery and now when i put the screen back on, in the down right corner it doesnt sit flush. Its raised a bit. Please help This is usually caused by how the screen flex cables are aligned. Take a look at the flex coming from the screen and notice that there is a silvery “chip” on the flex. If it isn’t aligned properly, it will impede the way the screen sits on the housing....

Chosen Solution Hi Guys. I have an iphone 6, i think with touch IC problem, because sometimes, the touch screen not work. I desolder both touch IC’s. And now the iphone dont turn on. I check with multimeter all caps (vcc main) are short. I dont desolder any EMI Shield. Any suggestion plz ?? Thanks Umar, If it was working fine and all you have done is removed the Meson and cumulus and now you have a VCC_Main short… Check the surrounding Caps in the photo to see if you may have bridged one of them....

Chosen Solution Hi all! i used our friend Google, and i searched iFixit forums but couldn’t find this problem, please help! :) Since a while we run in to trouble after replacing digitizers for the iPad Mini / Mini 2, Air and Air 2. This topic, i opened for the iPad Mini but the problem goes for all the above iPad models. The problem is after replacing the digitizer with High Quality digitizers from different suppliers ( more than 5 ) the Sleep / Wake function you normally get when opening the smart cover now also!...

Chosen Solution Any help here?? 55hx850 9/12/12 Display/Channel5/volume- didn’t show any errors SunNerd, this could be a TAB error or a cable error. Check the cable first. Make sure it does not have any tears or rips in it. Make sure that it is properly seated and that all pins are straight and no corrosion/dust or debris is on those. Should that not help, you could try and press on the top tab’ and see if that change the images....

Chosen Solution Surface Book 1/2 13.5" Adhesive Strips - iFixit for screen replacement or battery replacement ? From the description, says digitizer screen to frame. As for batteries, I typically use double sided tesa tape. I’ve done surface pros using tesa tape and it works out just fine btw. This adhesive film secures the front glass digitizer screen to the frame of your Microsoft Surface Pro 1/2 13.5". Complete your replacement of the front glass with new adhesive....

Chosen Solution Tablet says failed to mount external SD no such device. I have tried recovery system update,wipe cache partition,wipe data/factory reset,apply update from cache,update rkimage,update from external storage and apply update CV from adb, nothing works,screen is stuck on no command. All I did was turn the tablet on Check the USB port that you connect to your computer with. Look for bent pins or something lodged in the port ....

Chosen Solution I’m having a hard time with the bottom 2 pentalope screws to loosen up. I have a ifixit tool kit and using the P2. The bit is not catching the screw head. I have done this before and I am trying to be gentle with it. Trying to do a screen and battery replacement. Those pesky pentalopes…. They could of been stripped if they where cross threaded

Chosen Solution My printer doesn’t print at all and the cartridge carrier on my HP Officejet 6500A Plus doesn’t move when I open the cover Make sure it is getting electricity first then see if this guide helps: http://www8.hp.com/h22157/video-gallery/…

Chosen Solution When playing music or attempting to watch a video there is nothing coming out of the speakers of the device. There could be a problem with your devices audio hardware. Try to turn the device off then back on again. Most of the time this will reset the hardware and allow the speakers to produce sound again.

Chosen Solution Does the HDD Thermal Sensor cable is the same as the LCD Thermal Sensor cable ( and DVD Thermal Sensor Temperature ) ? Can I buy 3 of the same kind? Thank Here’s a listing of the systems thermal cables: LCD Temp Sensor cable - Apple P/N 922-9623Optical Drive Temp Sensor cable - Apple P/N 922-9624HD Drive Temp Sensor cable:Hitachi - 922-9215Seagate - 922-9216Western Digital - 922-9622 As you can see the cables are physically different!...

Chosen Solution One of the beaters on my mixer quit working shortly after purchase. I finally went back and just bought another one thinking it was just a fluke. Nope, it too will not hold a beater. One side will but the other just won’t hold!!! HELP!!!!’ I’m beginning to think it’s just the way the thing’s made maybe. Anyone else have this problem???? '' This video has instructions to install the beaters ....

Chosen Solution I can start it in safe mode, but it will not bring up the safe mode menu. Any ideas? You could have absolutely busted the hard drive, or broken solder joints in something. To properly tell whats wrong, I need you to take it apart and attach images

Chosen Solution I believe this cable attaches to the IR blaster, but I don’t know 100%. Shaped like a U. If there was somewhere I could pick up a replacement I would love to get a couple! Hi @leamsi , Is this what you need?

Chosen Solution I have an 2011 iMAC 27 desktop, recently a totally black screen shows up after turning it on, I can hear the chime sound, but the screen is totally black. Can anyone advise what could be the issue? And how to isolate it? Thanks, Most likely is a GPU failure. As Dan said an external monitor may help confirm this. This is a well know issue on this model and Apple had a repair program on it for a while but it has expired....

Chosen Solution I bought a used iPhone 6s a month ago, the previous owner had replaced the battery just before selling. As I got the phone, it showed that touch ID couldn’t be activated, the previous owner said he didn’t have that problem before the battery replacement. I didn’t think much of it until I started to notice that the battery was draining very fast, especially on standby. Also the home button gets hot when I’m not using the phone....

Chosen Solution I replaced the volume control cable and battery, and afterwards the rear facing camera produced just all black on screen. As a next step, I bought and replaced the camera. I was very careful to study all the ribbon placements, and I believe all the connectors are in place. Sometimes you can capture a picture of the black screen, sometimes you can activate flash, but most of the time the shutter button does nothing, as though taking long time exposure....