Posts

Chosen Solution I do the odd Samsung glass repairs, but the newer ones are obviously more of a pain. Rather than using cards to try and separate the lcd from the frame, is there anything really thin, flexible, and strong. Like some sort of flexible plastic which wouldn’t snap? Also, does anyone have any experience with these freeze machines, the videos of these makes the separation process look much easier. (Probably another technique to master) Thanks....

Chosen Solution The toggle switch is not working regularly. You have to fiddle with it, as it doesn’t want to move your picture up or down etc. I suppose that with “toggle” you mean what Canon calls the multi-controller, the directional button that is next to the upper right hand corner of the LCD screen. The most likely cause of the problem you’re having is that the response of the control has degraded due to dust, dirt, or sweat getting in....

Chosen Solution The top right corner came separated from the back side and I can’t get them to close back together. Is this because a screw got stripped or is there something I’m missing that I need to do to reattach the two sides of the case back together? Hi @timmer96 , You may have to remove the base cover and check what the problem is. The back cover screws into the palmrest assembly (top cover housing the keyboard etc)....

Chosen Solution I have a very old B&D TRO (no number after the TRO), and love it but it is probably on its last legs. The two top heating elements have stopped working and I’m wondering if there is a fuse somewhere I can check or did they come lose, or if it is time to get a new toaster oven. Thanks for your help! While doing a search for this I noted the prices....

Chosen Solution Hey guys, I have recently replaced iPad Pro 12.9 (1st Gen) Display. Everything was fine, except that suddenly the touch started acting erratically, and by that I mean, if I tap the bottom of the screen, the top of the screen registers unintended taps, I confirmed that with a Touch-Test App. Now, here is the thing, I figured out that by squeezing the bottom-left side of the iPad (see photo), touch works perfectly!...

Chosen Solution Pwr light blinks x3 after pwr cuts out abruptly why? Hi @cowboy559 , Here is a link to a website page that shows how to interpret the power light blink code for Toshiba laptops. Scroll down to post #3 on how to decode the pattern and up to post #2 to see what the code means. (post # are on bottom right side of post)

Chosen Solution I have a July 2011 Mac Mini with the A1347 logic board. I was installing a second hard drive today and things went smoothly, but I discovered that one component of the board fell off during servicing. It is a small square black component which I’m pretty sure is a resistor. There seem to be a few of the same component on the board, the writing on the component appears to be “L89” with a smaller “d” above it....

Chosen Solution Remove door panel to fix the electric window Hey, Leonard. If you can hear the motor running but the window won’t move the window has likely fallen off the regulator. You’ll need to take the door panel off to repair it. Good luck!

Chosen Solution My Flip 4’s battery went kaput. I researched how to swap the battery, purchased a replacement and was doing great until I realized that the original battery has swelled to the point that I’ve not been able to remove it. In trying to remove it, the wiring harness ripped off and a little fire started! I have a certified JBL repair facility two blocks away, but was hoping to get this done myself....

Chosen Solution I have tried to replace the battery in my mother’s DigiLand DL1010Q. Had all the tools as says in your DigiLand DL1010Q Battery Replacement Written By: Faith Lebo (and 2 other contributors) Tools Buy these tools Soldering Station Phillips #00 Screwdriver iFixit Opening Tools Spudger Parts No parts required. When I got down to the last step and said now what, guess I need to find the replacement part now and put my unit back together for now....

Chosen Solution My battery was drained so I replaced it using your repair kit. Followed all the steps and it turned on and I was happy but it was short lived as I found out it won’t charge now. I plugged it in to the wall, on to my laptop, and on to my iHome and it won’t charge at all. The thunderbolt symbol won’t show at all. What should I do?...

Chosen Solution My screen was cracked to smithereens but the iphone was still powering up and the touch screen still worked (it just shed little pieces of glass). Now I replaced the screen, following the directions, and the iphone won’t turn on. What should I check? How can I tell if the screen was defective or if I made a mistake? Thank you! Reanna the hard reset that Jamie is telling you to do is a good idea to start out, and you should hold the buttons for more like 30 seconds, if nothing happens then I would take the back off the phone and make sure the battery is connected properly, if all is well with that, then I would plug it into a charger and see if that makes it power on, if that doesn’t work open Itunes on your pc and plug the phone into it and see if its recognized, if it doesn’t the next thing would be to put it in dfu mode while its plugged in and try for a restore, here is how, http://www....

Chosen Solution How to replace a blower motor resistor in lincoln town car 2000? @puneetsingh your Lincoln does not have a Blower Motor Resistor in the conventional sense. It uses a blower motor speed control module . It’s located under the hood, mounted to the A/C evaporator housing on the passenger’s side rear of the engine compartment. This videoshows you the location and how to replace it. The video link from @jimfixer shows essentially the same information, just a different model bu same location same setup....

Chosen Solution hello. I have an iphone 6s plus whose screen is completely shattered with colored lines displayed on the screen and want to save the pictures which are in my phone on my laptop while deleting them on my phone. Can someone please tell me how to do it? You could try to connect your phone to an iTunes enabled computer. If you have previously “Trusted” that computer and have no PIN/password to unlock the phone, you will be able to backup the phone....

Chosen Solution Recently when I tried to use my AirPods with my MacBook Pro running macOS Mojave the right AirPod stopped playing sound and wouldn’t play sound at all. It works on other devices but not my MacBook Pro. Is this just a beta issue or is there a known fix. Please tell me this is not your main machine that you are running a beta on. Try your AirPod on your other Mac....

Chosen Solution I have two iPhone 6s 32gb phones. I broke the lcd and digitizer on one while hiking in the mountains. Fast forward. I took the logic board from the phone I broke and put it into the other iPhone which was activation locked. Everything worked except the screen wont respond to touch but the home button works (call this screen one). I took that screen off and replaced it with a screen I ordered off amazon and it causes the iPhone to overheat (call this screen two)....

Chosen Solution So, I recently replaced the screen on my iPhone 4. Everything went fine. Then the phone stopped keeping the proper time and would shut down randomly. I have spare parts laying around, so I tried different parts. I have two separate logistic boards and screens - both do exactly this while swapping them and interchanging them. Any reason behind this? Picture of the issue: https://ibb.co/ePBcfv That seems to be a screen cable damage....

Chosen Solution I just noticed that my 5C’s screen popped out of the plastic chassis on the top right corner. The phone was put in an Otter Box by the salesman the day I bought it and it was never dropped seriously (from my lap on a carpet once or twice, but no more than that). I’ve read somewhere that putting it on a flat surface and pressing on the back until it clicks back into place might work, but I’m scared it could break something, especially if it’s battery problem (like some macbooks I’ve seen) What do you think?...

Chosen Solution I do have a problem with my DSC-WX350 Setting zone, date and hour is permanently asked, never mind if I set correctly each time and this screen is displayed even when camera is off Seems that setting is not registered or kept in memory Any idea ? Thanks Hi @didiere , According to the user guide, the camera has an internal rechargeable battery that maintains the date and time settings (plus other user defined settings) when the camera is switched off and regardless of whether the main battery is charged or not....

Chosen Solution I have a Gameboy Advance SP of the model AGS 001, but want a better screen. Should I attempt to do this? Does replacing the ribbon have any other effects? Should I just buy a new Gameboy Advance SP that has a brighter screen? Is the screen too dim, I would not recommend to get new one or to get the display replaced The ribbon connectors are different between the two models, if you want to replace the screen, you’re going to have to get a pesky adapter that is really hard to fit into the shell....