Chosen Solution The internal data battery does not hold the date and time when replacing the main battery on my Olympus E-PL1. What type of battery is it? and where is it located? I hope you can help It’s likely that the camera uses a capacitor to keep the clock and memory up while changing the main battery. If the cap fails (as they sometime do) then you’ll see this problem....
Chosen Solution I have a 42" Vizio TV model SV421XVT. The sound stopped working. It seems as if the TV no longer reads the remote as I have to turn it off manually. Any ideas as to what this may be? Thanks in advance for your assistance. Michale Norton, first off start with what Vizio suggest on here: Built-In Speakers If you cannot hear any sound from the speakers built into your VIZIO TV, check the following: The volume level is set above zero....
Chosen Solution I recently purchased a second hand Toshiba 40L1533DB TV, when powered on initially all is fine, however the TV’s backlight turns off after some time. Interestingly, depending on the backlight mode, the time taken for the TV to turn of varies. On Low mode the TV’s backlight stays on for about an hour, but on medium or high this time is less. After turning the TV back on immediately after the failure, the backlight goes out again much sooner....
Chosen Solution I have recently bought HP Pavillion All in one 27 inch -d0014 PC. Its RAM is currently 16 GB. Can I upgrade it to 64 GB? What RAM can I buy? @Mehmet Çetik Hi Mehmet, Crucial says: https://www.crucial.com/compatible-upgra… So maximum is 32GB - what would you need 64GB for? Please tell? A larger SSD would be the best improvement.
Chosen Solution my rear a/c fan only operates at the high speed. where is the fan located. is there a resistor for the motor and if so where is it located? From the service manual :-): Remove the right rear quarter trim panel Disconnect the electrical connector from the blower motor resistor. Remove the retaining screws from the blower motor resistor. Remove the blower motor resistor (1) from the vehicle. Good Luck...
Chosen Solution when i put the view to the rear camera the image is really blurry but front camera view is great how can i fix it? It sounds like a problem with the lens of the camera. Make sure that: A.) There isn’t anything on it, such as film of scratches. B.) The lens cover isn’t cracked. C.) Try focussing the camera a few time and see what it does, if the camera is make a very loud noise when focusing it could be damaged....
Chosen Solution When trying to separate the male & female connectors in dsi I accidently pulled the female connector completely off the board. How do I repair? Thanks! Update Sorry.. power connector. I’m assuming that the reason the dsi now won’t power on because this piece is no longer attached to the board? The repair I was originally making was to just replace a scratched lower screen. THanks kvogel I believe that the power connector is solder on the logic board....
Chosen Solution I have an iMac Intel 20" EMC 2133 2.4 GHz Core 2 Duo Model A1224 which is having hard drive issues. I am looking at upgrading rather than replacing and trying to compare 3 available SSD drives which are all 500GB & pretty close in price: Crucial MX500, WD Blue, & Mercury Electra 3G. Any personal experience with any of these drives (or other recommendations) would be appreciated. My second question is: aside from the 3....
Chosen Solution the remote stopped functioning. i put in a fresh battery. when i press the remote, i get an orange lite on the unit. it works without the remote, manually. is there a serial number for the remote. will another remote work. is it an internal problem? I’d open it up and check the connections, here’s a question that tells how: How do I pull one of these apart?...
Chosen Solution R & r heater core 2004 neon how many hours It will take the better part of a day if you have a good idea what your doing . You will have to remove the dash and move a lot of dash related components. this is an excellent tear down explanation http://www.hpaircraft.com/neon/heater_co… Hope this helps
Chosen Solution I bought a screen to replace my cracked one about 2 months ago from an Indian shop (the new screen is not a genuine apple screen) . After a few days the new screen started flashing and has lines accross it, it varies in severity. Now over the last week or so the screen goes black if I open apps, it slowly fades to black and I either have to wait 20 minutes for it to work again or I have to press the home and the lock button to restart it....
Chosen Solution MB Pro A1398 mid-2014 i7 2.5 16gb 512gb 2gb gt750M Machine boots fine but runs slow. Scored about 1100 in geekbench 4 - single core/ 3000 multi-core. Same i7-4870HQ cpu in my MSI scores 4300 / 14000. Anyone seen this before? It does switch graphics but runs at like 25% and won’t turbo the cpu by the looks of it. It’s like temp sensor is gone bad, but ueing HWsensors/HWMonitor reports normal temps or the cpu is underfed :) starving....
Chosen Solution I have a Macbook Air with a shattered screen. I don’t need to whole LCD assembly just the screen. I took the Mac apart and now I am left with the LCD assembly. Do you know how I can dismantle it and swap the screen? If somebody can answer this question, I would really appreciate it. Aliabouelhouda@hotmail.com A company I use with my work is DT&T service and they can replace it for you for about $525....
Chosen Solution My samsung tablet has 32gb of storage. Someone told me when they broke theirs that there was a sd card slot inside. I don’t think this is true but I don’t want to open mine to find out. Does anyone know if this is true? If it is true is the slot used? If it is can I take the 32gb out and put a 64gb in? Thom Frost, the biggest complaint from owners of this table is the absence of a SD card reader....
Chosen Solution i have a S900 that had a Waste Ink Tank error indicated. I replaced the waste ink pads and now I cannot get the eprom to reset. When I turn it on the indicator light goes green then flashes 7 times. The reset procedure is invloved and I think that may be why I haven’t been able to get it reset. Do you work on this old a printer?...
Chosen Solution I shine a light and can see my desktop. And if I apply pressure on the LCD screen at some points and/or twist the screen slightly in an angle it lights back up like normal, but as soon as I release pressure it goes black. So the computer is working fine I can move the mouse and click on things it’s just gone completely black. I had this LCD screen replaced at a comp repair shop less than a year ago....
Chosen Solution I have the same problem as described here: How toReplace broken speaker for QC25. In short, the speaker on my right died. The question is where to buy the replacement part. It seems that this part is available on eBay for a range of prices, which warns me for cheap replacement parts. I am looking for a source for a quality replacement part, in order not force me to replace (=downgrade) the other, currently working side at the same time....
Chosen Solution We had a SQL server die due to some RAID problems. We sent the machine out to a data recovery company and they are able to recover the .MDF and .LDF files from the drives. Will I be able to use those files to restore the databases to a new machine? What do I need to watch out for? Thanks! Have u tried out the old way of creating empty database with same name....
Chosen Solution I’m looking for an SSD to USB adapter. The SSD in my model is no longer the standard SATA connection. Apple changed the interface on the SSD. The pin count on the SSD is 11+14. I need this adapter because the logic board died. I need to copy data from the SSD. I’m looking for a device where I can copy data from one of these newer style SSD drives....
Chosen Solution Replaced battery and screen on Surface Pro 5. After reassembling I powered on the device and started up ok, but a portion of the screen wasn’t responding. to touch. I shut it down and disassembled to check my connections but when I did I removed one of the connectors improperly. This damaged the pins slightly. I was able to gently bend them into place and when I pushed the ribbon cable into it seemed to connect in just fine....
