Posts

Chosen Solution how do I get the shaft out? I had a similar bread making machine and I might be wrong but I presume the assembly should be the same. If you remove the dough mixing container you will probably see an easily accessible resistance. By memory, if you look carefully inside, on the bottom metal plate you will find a few 2 dotted tamper proof screws. If you used the machine for quite some time, it will be probably difficult to spot them as the plate and everything are charred and rusted....

Chosen Solution the washer comes to the end an it has ol on it but you have to put it on spend to get all the water out First, OL stands for “Overload”, so in other words, the washer thinks the tub is too hard to move because it’s overloaded and the motor is struggling or the unit is way out of balance causing the washer to struggle. The most common problem is a nut below the inner tub that needs to “float”....

Chosen Solution Hello, I have an IPhone 6 plus. A couple months ago, I had dropped my phone and the screen cracked. I went to the mall and got the screen replaces; however, a couple days later, my phone randomly started twitching ( if that’s how you name it) and went black. I pressed the power button ( did not turn it off completely) and pressed it again and it was back to normal....

Chosen Solution I replaced the battery on my iPhone 6 with an IFixIt battery and randomly it shuts off. No warning. No spinning gear. It is just suddenly off. Plugging it into power gets it to come back up pretty quickly. When it powers back up it shows that there is plenty of power. It’s happened with 20%, 40% and even close to 100%. Is this just a battery that’s a dub?...

Chosen Solution I thought I had this figured out as a defrost timer issue, but not so sure. Checked continuity on temp control and got infinity reading when off and .2 when turned to cold position, (suggests part is good???). When refrigerator warmed again, I turned defrost timer and fridge began chilling. I assumed defrost timer to be stuck in defrost mode. when frig warmed again, I opened doors and while preparing to turn defrost timer again to see if I could repeat the first check, it started up on its own… when working it chills and freezes well....

Chosen Solution How do I disassemble the door to replace the latch and spring assembly? Microwave #721.85033010 I would strongly suggest to order the complete door. The door is easy to replace, just lift up. There is a risk of microwaves leaking after the door is dissasymbled A survey test is required after repairing a door. If you don’t own a survey meter and aren’t qualified to use one, then order a door....

Chosen Solution I have a Lenovo T430 with Ubuntu with an Intel i5 processor, but the motherboard is defective and I can’t power on my computer. If I buy a used motherboard from ebay where it says in the description “This unit has been tested to successfully power on and boot to the BIOS screen”, all I have to do is boot the computer as normal, and then it will enter Ubuntu and I can access all my old data just as before?...

Chosen Solution Do I have to replace my hard drive with the exact same brand? No, you don’t. But! you do need to use a special adapter cable as Apple leverages the HD’s internal thermal sensor to manage the systems cooling. Apple contracted special drives which are only available from Apple (which are very expensive!) Using this adapter cable: OWC - In-line Digital Thermal Sensor for iMac 2011 Hard Drive Upgrade allows you to put in any HD or if you want you could even put in a SSD instead....

Chosen Solution Hi all, I have a late 2011 15" Macbook Pro. I replaced the battery with one purchased from ifixit. The install was straightforward however I’m now getting intermittent random shut downs - the computer will lose all power (screen turns black etc). If I press the power indicator button on the side of the computer it will show no power for about 30 seconds. Then it will show the battery strength and the computer can be restarted....

Chosen Solution My battery had died and was causing issues so I replaced the battery now my trackpad works fine but my keyboard is unresponsive . I dunno what went wrong or how to correct it . I am willing to correct it and would appreciate any help and info anyone can provide . Pls . In principle nothing should go wrong with the keyboard when replacing the battery, since there’s no real overlapping of parts, so if any problem showed up just after replacement it’s probably job related....

Chosen Solution The HDD in this iMac was failing so I replaced it with a known good, apple certified HDD. After reconnected the HDD and reconnecting the LCD, I powered on the iMac. I can hear the fans power on, but there is no display on the LCD. After a few second I get a single beep every 5 seconds. Looking up beep codes says that this means RAM is not present....

Chosen Solution I posted a few weeks ago about my screen flickering - was told it was the LED Display Driver Board that needed replacing - so I did - I bought 2 just in case, and the first one, no change, second one, same, no change either. However, now the display won’t turn off - ever. The computer boots up, very white screen, then goes to the gray screen and all is normal....

Chosen Solution Sorry long read, but it pertains to trying to find a possible short of my iphone preventing the battery from charging. I own a iPhone 5S and discovered an interesting situation. I purchased a replacement battery for my iPhone 5S from another supplier, attempted to use it and the battery would not charge and simply drain to zero. The display would say the battery was charging and give the positive audio ding to indicate that the phone recognized the charging cable was plugged and charging....

Chosen Solution I have a chance to purchase a LM270WQ1-SDDB replacement screen. Will it fit into my 2010 27" imac. I can’t find an answer to this question. Most likely because we work off of Apples part numbers not the vendors (we don’t try to keep track of all of the suppler #s). The part you are looking for is Apples P/N: LCD Assembly, 27" 661-5568. With that you should be able to cross reference to a vendors part if the supplier offers it....

Chosen Solution I want to know how to replace a cracked ipod screen Use this guide to ID your iPod: http://www.ifixit.com/Info/ID-your-iPod after you ID your iPod get back to us and update your question with the information,or you can look for the parts and repair guides yourself using the “repairs” and “parts” links at the top of this page. You can choose your type of iPod from the types shown here, then choose the to see the glass panel replacement guide for your given model....

Chosen Solution my pc got the problem of screen resolution and it is showing out of range with black screen how can i solve it plz any 1 answer it If the display is showing you this message then the signal the PC is sending to your display is not one of the supported modes for the display. To fix this you’ll need to reconnect the old display (if you exchanged it out) so you can see the desktop and then go into the Display control panel and set the settings for what your new display is able to support....

Chosen Solution My phone’s display is completely gone and i have no intention of repairing it as i bought a new phone and display replacements are costly. I have some files inside it that i need and thus i connected it to pc via usb. The problem is that it will show the files only if the lock screen is open. Any help would be appreciable @notanidiot you will have to replace the display in order to access those files....

Chosen Solution When I was at school, I pulled out my phone and a few times the ringer would turn off on it’s own, and I usually keep it off. It was in the middle of class and it did it a couple of times. How do I make it stop? And I need to keep it off during school hours because I can’t have it ringing in the middle of class....

Chosen Solution I have a rather strange problem. I recently replaced my screen but in the process must have damaged something as the backlight began to flicker. I then replaced the display cable and the isight cable (which includes the power cable). This did not resolve the issue. Finally, I replaced the LED display driver board and now, the backlight will not turn off. Ever. As soon as there is a power source (power or battery) the backlight turns on, even though the computer is turned off....

Chosen Solution Hi there, my father’s iMac screen is no longer working, but the Mac obviously still boots. What I’ve been told: During use, the Mac “froze” (that’s what my father called it, I have unfortunately no closer details). He pulled the power cord, reconnected the Mac and turned it on. But the screen stayed black. What I’ve tried and found out so far: the Mac plays the boot soundthe Mac seems to start booting successfully (the hard drive is spinning and making noises)after booting, the Mac makes the ‘plop’ sounds when I use the keyboard’s volume buttons, so I assume the entire operating system is loading successfully I tried flushing the PRAM without any change (multiple attempts)I tried resetting the SMC without any change (multiple attempts)the screen is completely black; when using a flashlight, I can see no picture at all What I have not tried so far: connecting an external screen (need to get hold of a suitable adapter) Based on my observations, are there any obvious spots which I could check?...