Chosen Solution I need to replace my surface pro 3 screen and would appreciate a recommendation and link to the adhesive I should use on the new screen install. Thank you I have replaced a few Surface Pro 4 screens before and I used the adhesive best known as “red tape”. It comes in all types of widths and is fairly cheap. It creates a strong bond as I have not had any complaints....
Chosen Solution The PlayStation 3 hard disk’s file system is corrupted and it doesn’t restore when i press ‘ok’; it keeps repeating the same message. what do i do? Make sure the red light on your power button is RED. Place your finger on the power button, and hold it down. It will turn green, then eventually go red. Give or take 10 seconds. Release your finger. This lets the system know it’s fixing to enter Safe Mode....
Chosen Solution The washer does not fill, and water goes onto the floor and none in the washer. It does not leak when it is not trying to fill. gary.curry1955 pull the washer aways from the wall and check the supply hoses as well as the water inlet valve supply. Sounds like your water inlet supply is leaking since all the water for the washer comes from there. for more detailed help we would need to know your exact model number....
Chosen Solution Hi there. I made a “Frankenstein” iPhone 6 from the corpses of 3 other iPhone 6 that had various problems. It works fine but the battery is completely off - it doesn’t last much and gives off totally wrong charge values. Is there anything I can try before replacing the battery that could improve the issue? the battery and the motherboard come from different phones so maybe it needs to be calibrated....
Chosen Solution I actually have an HP Elitebook 8470p but its similar to the 8460p. Currently it has this random issue of not powering on and I don’t quite understand what the LED lights mean. Typically I can get it working by removing everything (ram, battery, cmos battery) and reinstalling the items until it runs again but its kind of annoying of having to do it everytime. Also note the orange LED light does not show even with the battery plugged in (idk why) although it still charges the battery....
Chosen Solution I’m thinking of putting new TIM on my rMBP. The ifixit guide goes over this but also talks about replacing the heatsink. Is getting a new heatsink critical or am I okay to reuse the original? Thanks in advance. Also, I’m getting about 50°C at idle and 80+°C at load (close to the TjMax of the cpu) To start off: I reuse the systems heatsink. But, in some cases the heat sink fails!...
Chosen Solution I replaced the battery on an iPod mini. When I dock it on the newest Bose Sound Dock I don’t get any sound, when I dock it on an ihome player or my old Bose Dock it plays fine. I get sound from the headphone jack fine. Also the cable that goes from the mini to USB on the computer is fine. I’m stumped. Thanks for all your help....
Chosen Solution Is it possible to replace the poly carbonate shell on a Macbook a1342 with the aluminum case of a a1278, as far as connectors and internals fitting? Hypothetically all things are possible. In the realm of reality with a lot of unorthodox ingenuity it could be done. However with the effort required to make such a thing happen I don’t consider it feasible to try. You would have to grind down all existing mounting towers for the screws and re-establish new ones in the appropriate places....
Chosen Solution Hi all, I got a MBP A1398 mid-2014. I want to replace my touchpad for a model from 2015. The 2015 model touchpad has a different click sound and feeling. Is it possible to install a newer version touchpad in my mid-2014 machine? Thank you No, you can’t replace your trackpad with a newer force touch model.
Chosen Solution I followed all the instructions on the rear camera replace and once phone was put back on, the camera does not work and the home button does not work….never had a problem with the home button… it seems like a software issue?…..do i need to do a hard start?…or a restore?.. You can a always do a force restart. But software probably isn’t your issue. If all you did was remove the display then try power cycling....
Chosen Solution The backlight works fine, can hear sound, but no picture. I just replaced the T-con board and still have the same issue. What should be my next step? Could it be the cables running to the T-con board? @savethatmoney return the T-con board and replace the main board.
Chosen Solution Just installed the replacement battery (4 times now) and every time I get the apple logo, but nothing else. I can put in my old battery (it was losing it’s charge cycle time) and it works fine. Not sure what’s causing the problem. Update Is there a way to test it with a multimeter to make sure? It’s a defective battery
Chosen Solution 1997 fF1504x4. Have a question about trans sensor.would a bad sensor cause the rpms to run up alittle before changing gears? Besides that it shifts great Usually if you get a sudden increase in revs before a shift The springs in the valve body are too stiff this is how a shift kit works makes the hit harder between gears so theres no power loss. Is this a recent development or did you just get the truck and notice this ....
Chosen Solution Salut, Svp une solution pour mon pc. Merci Hi, If Win 10 was installed in the laptop, here’s a link that may help you to fix it. Google translate: Salut, Si Win 10 a été installé sur l’ordinateur portable, voici un lien qui peut vous aider à le réparer.
Chosen Solution my screen is a half black ,what should I do ? loyan, this could be a bad LCD (broken backlight) as well as a signal issue. Disassemble your nook and take a look at the connector, make sure it is properly seated. If it is and the components do look okay, I would start with a replacement LCD. You are looking for a LD070WS2 (SL)(02) LCD, available at places like ebay for around $70....
Chosen Solution Hi! I’ve got an odd 15" aluminum that will not show video on its own screen unless it is connected to external video, in which case it comes on, and the external screen works fine as well. I’ve tried cycling through the external display modes, and booting up in each one. I’ve tried resetting the PMU, which works, but the machine’s PRAM will not reset – it just sits on a black screen endlessly....
Chosen Solution Hi! I ordered a replacement screen for my broken iphone from China and i replaced the screen succesfully. Seems to work fine but the bottom part near the home button doesnt close properly. Im afraid to press it too much because i am afraid it will break. I was able to screw back the pentalope screws but the corners wont go in. Has anyone else had this problem? Maybe the dimensions of the replacement screen are off a bit?...
Chosen Solution I put in my SD card in the camera and take some pictures but when I go to download them it say no pictures found. Here’s an answer on how to set it up to save to the SD card: How to transfer a picture from camera memory onto the SD card? From what I’m guessing, the SD card has been formatted in a way that the camera recognizes but the computer doesn’t....
Chosen Solution Hi everyone. This is a follow-up to my MacBook Air 13” (2014) – Water Damage, will not power on. Thanks to everyone who replied and helped out. I finally got the MBA to boot and just about everything works (keyboard, camera, etc), except for the capability of automatically switching from AC power to battery power. I have installed a brand new NewerTech battery (the old one wouldn’t hold a charge), it t was fully charged by the MBA and recognized by coconutBattery....
Chosen Solution Well, I’ll try and summarize the story. My Dad took a 12 pack of Diet Pepsi to his work on a day that was over 110 degrees Fahrenheit and forgot it in his car when he went in to work. I think you can see where this is going. All of the cans exploded and rocketed around the front seats. Big mess! The problem my Dad has now is that the passenger seat leather is so stiff it feels like sitting on a plywood board....
